Das Reflex V2 Werkzeugset ist jetzt kompakter und kommt mit einem Etui geliefert, welches die Werkzeuge schützt und Ordnung hält. Es beinhaltet alle notwendigen Schlüssel, um deinen RX28 zu montieren. Selbstverständlich gilt das auch für die allermeisten anderen 1/28 Chassis-Kits auf dem Markt. Das Werkzeugset enthält: Inbus-Schrauber:0,9mm1,3mm1,5 mmBox-Schlüssel:4.0mm4,5 mm Phillips-Schrauberzieher: #0
The Wing Things are designed to make mounting your wing much easier. Install the screw from the bottom of the body and thread them into the wing thing threads. You can hold the wing thing with a 4.5mm hex wrench to fully tighten.
The total weight of the 2 wing things and 2 M2x4 is roughly 0.5g; about the same weight as using a couple of steel hex nuts and 6mm steel screws that are typically included in body sets.
The Wing Things are designed to make mounting your wing much easier. Install the screw from the bottom of the body and thread them into the wing thing threads. You can hold the wing thing with a 4.5mm hex wrench to fully tighten.
The total weight of the 2 wing things and 2 M2x4 is roughly 0.5g; about the same weight as using a couple of steel hex nuts and 6mm steel screws that are typically included in body sets.
The Wing Things are designed to make mounting your wing much easier. Install the screw from the bottom of the body and thread them into the wing thing threads. You can hold the wing thing with a 4.5mm hex wrench to fully tighten.
The total weight of the 2 wing things and 2 M2x4 is roughly 0.5g; about the same weight as using a couple of steel hex nuts and 6mm steel screws that are typically included in body sets.
The new ride height gauge makes it easier to read Ride Height Readings on chassis and motor mounts particularly when they are chamfered like on the RX28.
These sleek-looking steel bumper weight set allow you to fine tune your weight bias on your Mini-Z when used in combination with any of our Carbon Fiber Bumpers. When running on bumpy or high grip environments, playing around with a little bit of nose weight can impact tremendously the behavior of your car. This weight set allows you to fine tune your nose weight in 1g increments. This is easily achieved by stacking the thru-hole weights and then clamping them down on the bumper with the threaded weight on top.
Included in the set is:
2x 1g thru weights
1x 1g threaded weight
1x M2x4CS Screw
1x M2x6CS Screw
M3 x 0.5mm Axle Shims to space out your rear axle and fine tune your set up (in some instances to center your rear axle!) Will Work on Cars like the GLR GT on the front as well.
Dieses Set-up Board ist aus 3mm Carbon Fiber gefertigt. Es misst 165x200mm und hat die perfekte Grösse, um bequem darauf zu arbeiten und in Deinem Koffer mitzureisen. Auf dem Setupboard befindet sich eine runde Wasserwaage und 4 verstellbare, gefräste Aluminiumfüsse, um das Setupboard eben aufzustellen und damit die Einstellungen für Dein Auto genauer zu machen. Die neue Version 2 des Boards enthält ausserdem gefräste Vertiefungen, damit Du lose Teile wie Karosserieclips und Radmuttern darin ablegen kannst. Video
Das Reflex V3 Werkzeugset - jetzt mit einem neuen Griff Design und zusätzlich mit einem Philips 00 Kreuzschraubenzieher, welcher sich bestens für die kleinen Pivot Schrauben des RX28 eignet. Das V3 Werkzeugset kommt wieder in einem praktischen Etui, welches die Werkzeuge schützt und Ordnung hält. Es beinhaltet alle notwendigen Werkzeugschlüssel, um deinen RX28, GL Racing, RTA oder MWX zu montieren. Das Werkzeugset enthält: Inbus-Schrauber:0,9mm1,3mm1,5 mmBox-Schlüssel:4.0mm4,5 mm Phillips-Schrauberzieher:#0#00
Solide, hochwertige Stahllager zu einem tollen Preis. Dies sind einige der besten Stahllager, die Sie heute bekommen können. Wenn Keramik nicht Ihr Ding sind, ist dies eine gute Ersatzlager für Ihre M3 Vorderachse Auto gesetzt.***Solid, high quality steel bearings at a great price. These are some of the best steel bearing you can get today. If ceramics are not your thing, this is a good replacement bearing set for your M3 Front Axle Car.
Während den Sommerferien vom 1. Juli bis zum 10. August 2024 kann die Bearbeitungszeit von Bestellungen 4-5 Tage betragen.
Wir danken euch für euer Verständnis und geniesst den Sommer und das schöne Wetter.