Product Type: MX EVO
RX-DSM2
Protocol: DSM/DSM2
Size: 10.0*13.5*3.5mm
Work Volt: 3.0V/3.3V
Reaction Time:
EVO->5.5ms - 4CH PWM->5.5/11ms
Support KYOSHO EVO
Mode (MR-03EVO/MA-03EVO): Yes
Support 4CH PWM OUTPUT
Mode: Yes
Support 1/72-1/64 RC
Car Mode: Yes
Support 1/43-1/24 RC
Car Mode: Yes
FW UPDATE: Yes
Kompatible Spektrum Fernsteuerungen:
DX2EDX3CDX4SDX5CDX5-ProDX5-Rugged
Anleitung
This RC receiver unit is Kyosho & Ko Propo ASF
compatible. It offers full 4-channel support in ultra- light weight and micro
size. It is ideal for micro racing cars.
Channels: 4CH
Weight: 3.5g
Dimension: 22×12mm
Compatibility
Compatible with ASF remote control system.
Suitable for remote control
KO PROPO EX-1 FHSS
KO PROPO EX-2
KO PROPO EX-6R
KO PROPO 903FH/904FH RF Module
Bind
- Press the BIND button and power on the receiver, the
receiver’s led will flash quickly.
- Put the transmitter into bind mode.
- The receiver’s led will flash slowly when the binding is
successful.
- Disconnect receiver’s power and reconnect the power cable
to the receiver.
- Now is should working normally.
FUTABA T-FHSS NANO 4CH TOWER ANTENNA RECEIVERVariante mit PVC Gehäuse Description:This RC receiver unit is FUTABA T-FHSS compatible. It offers full 4-channel support in ultra-light weight and micro size. Features:1. Futaba 2.4GHz T-FHSS compatible2. High performance CPU enhance precision control feeling3. 4 channel support4. Nano size (19mm x 12mm)5. Added failsafe function6. Operating Voltage 3.5V - 12V7. Weight: 3g Link Procedure:Each transmitter has an individually assigned, unique ID code. In order to start operation, the receiver must be linked with the ID code of the transmitter with which it is being paired. Once the link is made the ID code is stored in the receiver and no further linking is necessary unless the receiver is to be used with another transmitter.1-Place the transmitter and the receiver close to each other within half (0.5) meter.2-Place the transmitter into the linking mode and turn on the receiver3-During countdown, push the receiver tact switch for approximately 2 seconds. The LED will begin to blink red. After the receiver LED switches from blinking red to green - red steady light, If the transmitter and receiver are linked normally, set the power switch to the OFF position and then turn on the PWR ON position. If the receiver LED lights green, linking was succeeded. Actually check servo operation. Normal mode / High Speed mode:The‘Normal mode’accepts any type of servos or the peripheral. The "High Speed mode" only accepts the digital servos, including BLS series, and most peripheral equipment such as the brushless ESCs. Please pay special attention to the information contained within this manual and transmitter manual in order to have a pleasant running experience.
FLYSKY NB4 NANO 4CH TOWER ANTENNA RECEIVERVariante mit PVC Gehäuse! Description:This 2.4G RC receiver uses AFHDS3 protocol and it is dedicated to the FLYSKY Noble NB4 transmitter. It has single-antenna, use two-way transmission and features a unique compact design that saves space. Features:1. FLYSKY AFHDS3 protocol compatible2. High performance CPU enhance precision control feeling3. 4 channel servo signal4. Tower antenna provides both good receipt signal and space saving5. Nano size (19mm x 12mm)6. Added failsafe function7. Operating Voltage 3.5V - 12V8. Weight: 3g Binding:1. Press the BIND button and power on the receiver, the receiver’s led will flash quickly.2. Put the transmitter into bind mode. The receiver’s led will flash slowly when the binding is successful.3. Disconnect receiver’s power and reconnect the power cable to the receiver. Now is should working normally. Compatible Transmitters:FLYSKY Noble NB4FLYSKY Noble NB4 ProFLYSKY PL18 Package Included:1 x Receiver4 x 1.5mm 3P JST plug with high quality silicon cable
This 2.4G RC receiver uses AFHDS3 protocol and it is dedicated to the FLYSKY Noble NB4 transmitter. It has single-antenna, use two-way transmission and features a unique compact design that saves space.
Features:
1. FLYSKY AFHDS3 protocol compatible
2. High performance CPU enhance precision control feeling
3. Integrated high performance dual sensitivity GYRO with EPA setup
4. Tower antenna provides both good receipt signal and space saving
5. Nano size (19mm x 12mm)
6. Added failsafe function
7. Operating Voltage 3.5V - 12V
8. Weight: 3g
Binding:
1. Press the BIND button and power on the receiver, the receiver’s led will flash quickly.
2. Put the transmitter into bind mode. The receiver’s led will flash slowly when the binding is successful.
3. Disconnect receiver’s power and reconnect the power cable to the receiver. Now is should working normally.
GYRO sensitivity Adjustment:
The gyro sensitivity is controlled by CH3 value which could be adjusted on the transmitter. When the CH3 value is 50%, the sensitivity is zero. Turn CH3 value to 0% or 100% both can reach 100% sensitivity. Turn CH3 value to 0% or turn CH3 value to 100% will have different sensitivity curve. The GYRO provides 2 different optimized sensitivity curves for drifting.
Gyroscope EPA Adjustment:
First adjust (left and right steering) on the transmitter, the EPA value you need. EPA (Travel) Setting (Gyro forward setting):
Press the "SETUP" button, turn on the GYRO. When the LED starts blinking fast, wait for the LED to blink slowly and the gyroscope is now in EPA (travel) setup mode, release the "SETUP" button. First turn the remote control to the left "EPA" position (the left end of the chassis) and stop there for a few seconds, when the left "EPA" position is saved in the gyroscope, the servo will automatically return to the middle position. Then turn the remote to the correct "EPA" position (right end position of the chassis) and stop there for a few seconds, when the correct "EPA" position is saved in the GYRO and EPA (drive) settings, the SERVO will automatically return to The middle position has been completed.
EPA (Travel) Setting (Gyro Reverse Setting):
Press the "SETUP" button, turn on the GYRO. When the LED starts blinking fast, wait for the LED to blink slowly and the gyroscope is now in EPA (travel) setup mode, release the "SETUP" button. First turn the remote control to the right "EPA" position (the right end of the chassis) and stop there for a few seconds, when the left "EPA" position is saved in the gyroscope, the servo will automatically return to the middle position. Then turn the remote to the "EPA" position on the left (left end position of the chassis) and stop there for a few seconds, when the correct "EPA" position is saved in the GYRO and EPA (drive) settings, the SERVO will automatically return to the middle position has been completed.
After the above settings are completed, please re-adjust the EPA value on the transmitter, and adjust the value according to the steering of your car chassis to the value you need.
Compatible Transmitters:
FLYSKY Noble NB4
FLYSKY Noble NB4 Pro
FLYSKY PL18
Package Included:
1 x Receiver
4 x 1.5mm 3P JST plug with high quality silicon cable
Ko Propo / Kyosho ASF NANO 4CH RECEIVERVariante mit Kunststoff-Gehäuse
Description:This RC receiver unit is KYOSHO ASF compatible. It offers full 4-channel support in ultra-light weight and micro size. It is designed for micro racing cars. Features:1. KYOSHO 2.4GHz ASF compatible2. High performance CPU enhance exactness control feeling3. 4 channel support4. Micro size (19mm x12mm)5. Ideal for any micro RC racing chassis6. Added failsafe function7. Operating Voltage 3.7V - 8.4V:8. ProductWeight: 2g Compatible Transmitters:KO PROPO EX-1 ASFKO PROPO EX-6RKO PROPO EX-6KYOSHO KT-18KO PROPO EX-5UR ASFKO PROPO 901SM/902SM RF Module Package Included:1 x Receiver2 x 1.5mm 3P JST plug with cable Bind and Failsafe:Power on your transmitter and receiver. Adjust transmitter each channel to the exact position you want to have in failsafe mode. Transmitter set to pair mode. Receiver led should be on. Long press the pair button. After around 2 seconds the LED will turn to fast flashing first then turn to on status again. Now the pairing is done and the failsafe data is saved. Power off the transmitter and receiver then power on again then the receiver will work.
SANWA NANO 4CH TOWER ANTENNA RECEIVERModel mit PVC Gehäuse Description:This RC receiver unit is Sanwa FHSS-4 and FHSS-3 compatible. It offers full 4-channel support in ultra-light weight and micro size. Features:1. Sanwa 2.4GHz FH3/FH4 Selectable Via Transmitter2. High performance CPU enhance precision control feeling3. 4 channel support4. Micro size (19mm x 12mm)5. Added failsafe function6. Operating Voltage 3.5V - 12V7. Weight: 3g Binding:1. Press the BIND button and power on the receiver, the receiver’s led will flash quickly.2. Put the transmitter into bind mode. The receiver’s led will flash slowly when the binding is successful.3. Disconnect receiver’s power and reconnect the power cable to the receiver. Now is should working normally. Compatible Transmitters:Sanwa M17Sanwa M12SSanwa M12Sanwa MT44Sanwa MT4SSanwa MT4Sanwa M11X Package Included:1 x Receiver4 x 1.5mm 3P JST plug with high quality silicon cable
MX EVO BA1 ManualMX EVO BA1 is a switching work mode product developed for MX EVO RX series products . After the MX EVO RX is installed in the EVO BA1 , the MX EVO RX works in the 4CH PWM standard signal mode .Features :Size: 16 . 2*15 . 2*6 . 5mm;Weight: 0 . 95g;Working voltage: 3 . 5V ~ 8 . 5V;Let all products of MX EVO RX series output 4CH PWM signal;Provide online firmware interface for MX EVO RX series products (Note 1) .Note 1: MX EVO RX -SANWA V2 . 15 does not support online firmware upgrade , but can read firmware version andother information .Interface (EVO BA1 on the left, EVO BA1 with MX EVO RX-SANWA installed on the left):CH1: STCH2: THCH3: AUX1CH4: AUX2/DATA(Online firmware upgrade interface)GUI download link: update . crossover -rx . com/mxo .zip
This RC receiver unit is Kyosho & Ko Propo ASF
compatible. It offers full 4-channel support in ultra- light weight and micro
size. It is ideal for micro racing cars.
Channels: 4CH
Weight: 3.5g
Dimension: 19×12mm
Compatibility
Compatible with ASF remote control system.
Suitable for remote control
KO PROPO EX-1 FHSS
KO PROPO EX-2
KO PROPO EX-6R
KO PROPO 903FH/904FH RF Module
Bind
- Press the BIND button and power on the receiver, the
receiver’s led will flash quickly.
- Put the transmitter into bind mode.
- The receiver’s led will flash slowly when the binding is
successful.
- Disconnect receiver’s power and reconnect the power cable
to the receiver.
- Now is should working normally.
This RC receiver unit is Sanwa FHSS-4 and FHSS-3 compatible.It offers full 4-channel support in ultra- light weight and micro size. It is ideal for micro racing cars.
Voltage: 3.3V~8.4V Channels: 4CH
Weight: 2g
Dimension: 19×12mm
PWM Mode: Normal/ SHR/ SSR Compatibility
Compatible with FH4T no FH3 remote control system.
Suitable for remote control M12,M11X,EXZES X,MT-4,GEMINI X,MT-S,MT-4S,M12S,EXZES-ZZ,M17.
Bind - Press the BIND button and power on the receiver, the receiver’s led will flash quickly.
- Put the transmitter into bind mode.- The receiver’s led will flash slowly when the binding is successful.
- Disconnect receiver’s power and reconnect the power cable to the receiver.
- Now is should working normally.
Contains: 3 JST sockets (1 spare), 10cm heat shrink tubing (enough for 2 attempts).
WARNING: For people with good soldering skills ONLY!!!
WARNING: Convert your Receiver at your our risk, Receiver warranty void
For people looking for a quick and easy solution, please consider our adapters instead:
Receiver Einheit für das Mini-Z Evo Board kompatibel mit der FLYSKY Noble NB4 Fernsteuerung.Technische Daten:Funkfrequenz: 2,4 GHzDrahtloses Protokoll: AFHDS 3Reichweite: > 50m (Boden)Antennentyp: EinzelantenneAbmessungen: 20*14*3,5 mmkompatibel mit Mini-z EVO Board
Receiver Einheit für das Mini-Z Evo Board kompatibel mit FUTABA T-FHSS Fernsteuerungen.Technische Daten:Funkfrequenz: 2,4 GHzDrahtloses Protokoll:
T-FHSS
Reichweite: > 50m (Boden)Antennentyp: EinzelantenneAbmessungen: 20*14*3,5 mmkompatibel mit Mini-z EVO Board
GMR ist ein neuer, von FlySky entwickelter 4CH-Mikroempfänger für 1:28 RC Racer , mit einer Reaktionszeit von nur 5 ms, geeignet für verschiedene Miniautos (Driften/Race), mit einer eingebauten Gyroskop-Schnittstelle und basierend auf dem neuesten AFHDS3-Protokoll. GMR verwendet ein präziseres Schaltungsdesign, welches den GMR kompakter und leichter macht (2,35*1,35*0,7cm/1,7g). GMR hat eine eingebaute Gyroskop-Schnittstelle.Weitere Merkmale von GMR: Unterstützt Online-Upgrade, mit umfangreichen Funktionen ständig aktualisiert. Unterstützt Zwei-Wege-Kommunikation und liefert die Statusinformationen in Echtzeit. Unterstützt 3,5-9V Weitbereichsspannungseingang, wodurch die Spannungsgrenze des Geräts überschritten wird. Vollständig an Noble NB4 anpassbar, mit umfangreichen Funktionen und sofortiger Entsperrung. Download ManualProduct
Model: GMR
PWM
Channel: 4
Wireless
Frequency: 2.4GHz
Wireless
Protocol: AFHDS 3
Range: >50m
(Ground)
Antenna
Type: single antenna (32mm)
Power:
3.5-9V
RSSI:
Supported
Data port:
PWM
Temperature
range: -10 ℃ — + 60 ℃
Humidity
range: 20% -95%
Online
Update: Yes
Dimensions:
23.5*13.5*7mm
Weight:
1.7g
Certification:
CE, FCC ID: N4ZGMR00
Product Type: MX EVO
RX-SANWA
Protocol:
SANWA-FH3/FH4
Size: 10.0*15.0*3.5mm
Work Volt: 3.0V/3.3V
Reaction Time:
EVO->2.6ms - 4CH PWM->5.6ms
Support KYOSHO EVO
Mode (MR-03EVO/MA-03EVO): Yes
Support 4CH PWM OUTPUT
Mode: Yes
Support 1/72-1/64 RC
Car Mode: Yes
Support 1/43-1/24 RC
Car Mode: Yes
FW UPDATE: No
Radio Compatible:
Sanwa M17Sanwa M12Sanwa M12SSanwa MT44Sanwa MT4Sanwa MT4SSanwa M11XAnleitung
This RC receiver unit is Flysky Flysky e Kyosho compatible.It offers full 4-channel support in ultra-light weight and micro size.It is ideal for micro racing cars.
Voltage: 3.3V-8.4V Channels: 4CH
Weight: 2g
Dimension: 19×12mm
Compatibility: FLYSKY GT2, GT2B, GT2E, GT2F, GT2G
FLYSKY GT3B, GT3C, IT4S
FLYSKY I4X, I6, I6X, CT6B, T6.
FLYSKY TH9X, TH9A, TM10, I8, I10
KYOSHO KT-432PT Bind
- Press the BIND button and power on the receiver, the receiver’s led will flash quickly.
- Put the transmitter into bind mode.
- The receiver’s led will flash slowly when the binding is successful.
- Disconnect receiver’s power and reconnect the power cable to the receiver.
- Now is should working normally.
This RC receiver unit is Kyosho/KO-FHSS full range of remote controls compatible. It offers full 4-channel support in ultra-light weight and micro size. It is designed for micro racing cars.
Features1)Modulation:Compatible all Kyosho/KO-FHSS2)Small size: 19*12mm(not including antenna)3)Super light: 2g(including antenna)4)Working voltage:3.7~8.4V5)High performance CPU enhance exactness control feeling6)4 channel support7)Added failsafe function8)Ideal for any micro RC racing chassis9)Comes with 3P 1.5mm plug
Kompatible Fernsteuerungen:
Kyosho KT-432Kyosho KT-531
Bind and FailsafePower on your transmitter and receiver. Adjust the transmitter for each channel to the exact position you want to have in failsafe mode. Transmitter set to pair mode. The receiver led should be on. Long press the pair button. After around 2 seconds the LED will turn to fast flashing first then turn to on status again. Now the pairing is done and the failsafe data is saved. Power off the transmitter and receiver then power on again then the receiver will work.
This RC receiver unit is Sanwa FHSS-4 and FHSS-3 compatible.It offers full 4-channel support in ultra- light weight and micro size. It is ideal for micro racing cars.
Voltage: 3.3V~8.4V Channels: 4CH
Weight: 2g
Dimension: 21×12mm
PWM Mode: Normal/ SHR/ SSR Compatibility
Compatible with FH4T no FH3 remote control system.
Suitable for remote control M12,M11X,EXZES X,MT-4,GEMINI X,MT-S,MT-4S,M12S,EXZES-ZZ,M17.
Bind - Press the BIND button and power on the receiver, the receiver’s led will flash quickly.
- Put the transmitter into bind mode.- The receiver’s led will flash slowly when the binding is successful.
- Disconnect receiver’s power and reconnect the power cable to the receiver.
- Now is should working normally.
This RC receiver unit is Flysky Noble NB4 & PL18 compatible. It offers full 4-channel support in ultra- light weight and micro size. It is ideal for micro racing cars.
Voltage: 3.3V~8.4V
Channels: 4CH
Weight: 2g
Dimension: 22×12mm
Suitable for remote control
Flysky Noble NB4
Flysky PL18
Bind
- Press the BIND button and power on the receiver, the receiver’s led will flash quickly.
- Put the transmitter into bind mode.
- The receiver’s led will flash slowly when the binding is successful.
- Disconnect receiver’s power and reconnect the power cable to the receiver.
- Now is should working normally.
This RC receiver unit is Flysky Noble NB4 & PL18 compatible. It offers full 4-channel support in ultra- light weight and micro size. It is ideal for micro racing cars.
Voltage: 3.3V~8.4V
Channels: 4CH
Weight: 2g
Dimension: 19×12mm
Suitable for remote control
Flysky Noble NB4
Flysky PL18
Bind
- Press the BIND button and power on the receiver, the receiver’s led will flash quickly.
- Put the transmitter into bind mode.
- The receiver’s led will flash slowly when the binding is successful.
- Disconnect receiver’s power and reconnect the power cable to the receiver.
- Now is should working normally.
FS-RM005 is a module used with Flysky Noble NB4.It adopts Mini-Z FHSS system and can be adapted to Kyosho Mini-Z RWD, AWD, 4X4, FWD and Buggy.
Product Model: FS-RM005
Built for: Flysky Noble NB4
Wireless Frequency: 2.4GHz
Transmission power: <20 dBm (EU)
Wireless Protocol: Mini-Z(FHSS)
Power: 3.3±0.1V
Antenna type: Built-in single antenna
Temperature range: -10 ? — + 60 ?
Humidity range: 20% -95%
Online Update: Yes
Dimensions: 34*18*5.2mm ( without the protective cover)
Weight: 2.3g
Certification: CE,MIC,FCC ID:N4ZRM005
Notice: Before using the FS-RM005, the Noble NB4 should be uploaded to the FW 2.0.99 (check the changelog carefully before updating)
Installation1. Remove the base of the NB4 correctly install the module into the transmitter handle, click [Model ], select the radio frequency setup as Mini-Z (FHSS);2. Power on the receiver while pressing the receiver’s bind button, and the receiver’s LED light flashes quickly;3. Click [Rx SET] and select the Bind Set. After the receiver flashes slowly, the transmitter will exit the code matching state, and the receiver indicator will always be on to indicate successful code matching;4. Check whether the transmitter, receiver, and model work normally. If you need to bind again, please repeat steps 2-3.
CompatibilityThe FS-RM005 module is compatible with NB4, etc.The FS-RM005 module is compatible with Kyosho FHSS Mini-Z RWD AWD 4X4 FWD and Buggy. etc.
This is the first Futaba T-FHSS compatible micro surface receiver in the world. It offers full 4-channel support in ultra-light weight and micro size. It is ideal for micro racing cars.
Features:1. Futaba 2.4GHz T-FHSS compatible2. High performance CPU enhance precision control feeling3. 4 channel support4. Micro size (19mm x12mm)5. Ideal for any micro rc racing chassis6. Added failsafe function7. Operating Voltage 3.7V - 8.4V:8. Weight: 2g Compatible Transmitters:Futaba 7PX 4PX 7XC 4GRS 4PV 4PM 4PLS Transmitter Two-way High Speed ReceiverPackage Included:1 x Receiver Procedure:Each transmitter has an individually assigned, unique ID code. In order to start operation, the receiver must be linked with the ID code of the transmitter with which it is being paired. Once the link is made the ID code is stored in the receiver and no further linking is necessary unless the receiver is to be used with another transmitter.Place the transmitter and the receiver close to each other within half (0.5) meter.Place the transmitter into the linking mode and turn on the receiverDuring countdown, push the receiver tact switch for approximately 2 seconds. The LED will begin to blink red. After the receiver LED switches from blinking red to green - red steady light, If the transmitter and receiver are linked normally, set the power switch to the OFF position and then turn on the PWR ON position. If the receiver LED lights green, linking was succeeded. Actually check servo operation. Normal mode / High Speed mode:The " Normal mode " accepts any type of servos or the peripheral. The "High Speed mode" only accepts the digital servos, including BLS series, and most peripheral equipments such as the brushless ESCs. Please pay special attention to the information contained within this manual and transmitters manual in order to have a pleasant running experience.