Mit diesem Werkzeug von TAR kannst du die Reflex Speed Dish Side Walls mühelos ab der Felge nehmen.Einfach Abziehwerkzeug von hinten in den Felge drücken und die Side Wall ausstossen.Material: 3D printedFarbe: orangeLieferumfang: 1 Stück
Designed to make your life easier. These plates lock into your favorite Reflex Racing Speed Dish wheels for an increased wheel lip diameter. Having a larger diameter lip on the wheel leads to a smaller side wall aspect ratio on your tire, which very effectively reduces traction roll and steering response on your car. These plates are optimized to be used with "Low Profile" style front tires, which when mounted measure around 23.0mm on our wheels. The plate set comes with 4 different sizes: 22.0, 22.2, 22.4 and 22.6mm. How to use: Start with a 23.0mm Diameter Mounted front tire on a speed dish wheel. (We recommend having glued the tire to the wheel, but you no longer have to add superglue to the sidewall.) Install the 23.6mm plate by pressing the 4 prongs into 4 of the 8 slots on the wheel. Make sure it seats all the way. DRIVE!!!It will still take a few laps or maybe half a run to break in your tires, depending on whether you trued or not, but once they do, the car should drive with really good balance. When you notice the steering start dropping off, or if you simply need more steering, go to the next smaller plate. Rinse and repeat.
All new from Reflex Racing is the Speed Dish Line of wheels. Designed with performance and durability in mind, these molded wheels have a 0.5mm outer ridge that matches the inner flange height of most 1/28 scale wheels. The result from this is a tire that is easier to glue (which we recommend) and also more stability to the tire in the case you prefer to use tape. Made from durable and tough glass reinforced nylon, these wheels are acetone safe so they can be re-used.The Taller aspect of the wheel makes the sidewall effectively smaller in order to also aid in the increase of corner speed.
The 14mm +1 provides a little more stability than the +0 rear and limits rotation a little bit. The result is typically a little easier to drive car.
All new from Reflex Racing is the Speed Dish Line of wheels. Designed with performance and durability in mind, these molded wheels have a 0.5mm outer ridge that matches the inner flange height of most 1/28 scale wheels. The result from this is a tire that is easier to glue (which we recommend) and also more stability to the tire in the case you prefer to use tape. Made from durable and tough glass reinforced nylon, these wheels are acetone safe so they can be re-used.The Taller aspect of the wheel makes the sidewall effectively smaller in order to also aid in the increase of corner speed.
The 14mm +1 provides a little more stability than the +0 rear and limits rotation a little bit.
The result is typically a little easier to drive car.
Offest: -1.5mmAll new from Reflex Racing is the Speed Dish Line of wheels. Designed with performance and durability in mind, these molded wheels have a 0.5mm outer ridge that matches the inner flange height of most 1/28 scale wheels. The result from this is a tire that is easier to glue (which we recommend) and also more stability to the tire in the case you prefer to use tape. Made from durable and tough glass reinforced nylon, these wheels are acetone safe so they can be re-used.The Taller aspect of the wheel makes the sidewall effectively smaller in order to also aid in the increase of corner speed.
Offest: -1.5mm
All new from Reflex Racing is the Speed Dish Line of wheels. Designed with performance and durability in mind, these molded wheels have a 0.5mm outer ridge that matches the inner flange height of most 1/28 scale wheels. The result from this is a tire that is easier to glue (which we recommend) and also more stability to the tire in the case you prefer to use tape. Made from durable and tough glass reinforced nylon, these wheels are acetone safe so they can be re-used.The Taller aspect of the wheel makes the sidewall effectively smaller in order to also aid in the increase of corner speed.
Offest: -1.5mm
All new from Reflex Racing is the Speed Dish Line of wheels. Designed with performance and durability in mind, these molded wheels have a 0.5mm outer ridge that matches the inner flange height of most 1/28 scale wheels. The result from this is a tire that is easier to glue (which we recommend) and also more stability to the tire in the case you prefer to use tape. Made from durable and tough glass reinforced nylon, these wheels are acetone safe so they can be re-used.The Taller aspect of the wheel makes the sidewall effectively smaller in order to also aid in the increase of corner speed.
All new from Reflex Racing is the Speed Dish Line of wheels. Designed with performance and durability in mind, these molded wheels have a 0.5mm outer ridge that matches the inner flange height of most 1/28 scale wheels. The result from this is a tire that is easier to glue (which we recommend) and also more stability to the tire in the case you prefer to use tape. Made from durable and tough glass reinforced nylon, these wheels are acetone safe so they can be re-used.The Taller aspect of the wheel makes the sidewall effectively smaller in order to also aid in the increase of corner speed.
Designed to make your life easier. These plates lock into your favorite Reflex Racing Speed Dish wheels for an increased wheel lip diameter. Having a larger diameter lip on the wheel leads to a smaller side wall aspect ratio on your tire, which very effectively reduces traction roll and steering response on your car. These plates are optimized to be used with "Low Profile" style front tires, which when mounted measure around 23.0mm on our wheels. The plate set comes with 4 different sizes: 22.0, 22.2, 22.4 and 22.6mm. How to use: Start with a 23.0mm Diameter Mounted front tire on a speed dish wheel. (We recommend having glued the tire to the wheel, but you no longer have to add superglue to the sidewall.) Install the 23.6mm plate by pressing the 4 prongs into 4 of the 8 slots on the wheel. Make sure it seats all the way. DRIVE!!!It will still take a few laps or maybe half a run to break in your tires, depending on whether you trued or not, but once they do, the car should drive with really good balance. When you notice the steering start dropping off, or if you simply need more steering, go to the next smaller plate. Rinse and repeat.
Designed to make your life easier. These plates lock into your favorite Reflex Racing Speed Dish wheels for an increased wheel lip diameter. Having a larger diameter lip on the wheel leads to a smaller side wall aspect ratio on your tire, which very effectively reduces traction roll and steering response on your car. These plates are optimized to be used with "Low Profile" style front tires, which when mounted measure around 23.0mm on our wheels. The plate set comes with 4 different sizes: 22.0, 22.2, 22.4 and 22.6mm. How to use: Start with a 23.0mm Diameter Mounted front tire on a speed dish wheel. (We recommend having glued the tire to the wheel, but you no longer have to add superglue to the sidewall.) Install the 23.6mm plate by pressing the 4 prongs into 4 of the 8 slots on the wheel. Make sure it seats all the way. DRIVE!!!It will still take a few laps or maybe half a run to break in your tires, depending on whether you trued or not, but once they do, the car should drive with really good balance. When you notice the steering start dropping off, or if you simply need more steering, go to the next smaller plate. Rinse and repeat.
Designed to make your life easier. These plates lock into your favorite Reflex Racing Speed Dish wheels for an increased wheel lip diameter. Having a larger diameter lip on the wheel leads to a smaller side wall aspect ratio on your tire, which very effectively reduces traction roll and steering response on your car. These plates are optimized to be used with "Low Profile" style front tires, which when mounted measure around 23.0mm on our wheels. The plate set comes with 4 different sizes: 22.0, 22.2, 22.4 and 22.6mm. How to use: Start with a 23.0mm Diameter Mounted front tire on a speed dish wheel. (We recommend having glued the tire to the wheel, but you no longer have to add superglue to the sidewall.) Install the 23.6mm plate by pressing the 4 prongs into 4 of the 8 slots on the wheel. Make sure it seats all the way. DRIVE!!!It will still take a few laps or maybe half a run to break in your tires, depending on whether you trued or not, but once they do, the car should drive with really good balance. When you notice the steering start dropping off, or if you simply need more steering, go to the next smaller plate. Rinse and repeat.
All new from Reflex Racing is the Speed Dish Line of wheels. Designed with performance and durability in mind, these molded wheels have a 0.5mm outer ridge that matches the inner flange height of most 1/28 scale wheels. The result from this is a tire that is easier to glue (which we recommend) and also more stability to the tire in the case you prefer to use tape. Made from durable and tough glass reinforced nylon, these wheels are acetone safe so they can be re-used.The Taller aspect of the wheel makes the sidewall effectively smaller in order to also aid in the increase of corner speed.
The 14mm +1 provides a little more stability than the +0 rear and limits rotation a little bit.
The result is typically a little easier to drive car.
All new from Reflex Racing is the Speed Dish Line of wheels. Designed with performance and durability in mind, these molded wheels have a 0.5mm outer ridge that matches the inner flange height of most 1/28 scale wheels. The result from this is a tire that is easier to glue (which we recommend) and also more stability to the tire in the case you prefer to use tape. Made from durable and tough glass reinforced nylon, these wheels are acetone safe so they can be re-used.The Taller aspect of the wheel makes the sidewall effectively smaller in order to also aid in the increase of corner speed.
All new from Reflex Racing is the Speed Dish Line of wheels. Designed with performance and durability in mind, these molded wheels have a 0.5mm outer ridge that matches the inner flange height of most 1/28 scale wheels. The result from this is a tire that is easier to glue (which we recommend) and also more stability to the tire in the case you prefer to use tape. Made from durable and tough glass reinforced nylon, these wheels are acetone safe so they can be re-used.The Taller aspect of the wheel makes the sidewall effectively smaller in order to also aid in the increase of corner speed.
All new from Reflex Racing is the Speed Dish Line of wheels. Designed with performance and durability in mind, these molded wheels have a 0.5mm outer ridge that matches the inner flange height of most 1/28 scale wheels. The result from this is a tire that is easier to glue (which we recommend) and also more stability to the tire in the case you prefer to use tape. Made from durable and tough glass reinforced nylon, these wheels are acetone safe so they can be re-used.The Taller aspect of the wheel makes the sidewall effectively smaller in order to also aid in the increase of corner speed.
All new from Reflex Racing is the Speed Dish Line of wheels. Designed with performance and durability in mind, these molded wheels have a 0.5mm outer ridge that matches the inner flange height of most 1/28 scale wheels. The result from this is a tire that is easier to glue (which we recommend) and also more stability to the tire in the case you prefer to use tape. Made from durable and tough glass reinforced nylon, these wheels are acetone safe so they can be re-used.The Taller aspect of the wheel makes the sidewall effectively smaller in order to also aid in the increase of corner speed.
All new from Reflex Racing is the Speed Dish Line of wheels. Designed with performance and durability in mind, these molded wheels have a 0.5mm outer ridge that matches the inner flange height of most 1/28 scale wheels. The result from this is a tire that is easier to glue (which we recommend) and also more stability to the tire in the case you prefer to use tape. Made from durable and tough glass reinforced nylon, these wheels are acetone safe so they can be re-used.The Taller aspect of the wheel makes the sidewall effectively smaller in order to also aid in the increase of corner speed.
All new from Reflex Racing is the Speed Dish Line of wheels. Designed with performance and durability in mind, these molded wheels have a 0.5mm outer ridge that matches the inner flange height of most 1/28 scale wheels. The result from this is a tire that is easier to glue (which we recommend) and also more stability to the tire in the case you prefer to use tape. Made from durable and tough glass reinforced nylon, these wheels are acetone safe so they can be re-used.The Taller aspect of the wheel makes the sidewall effectively smaller in order to also aid in the increase of corner speed.
All new from Reflex Racing is the Speed Dish Line of wheels. Designed with performance and durability in mind, these molded wheels have a 0.5mm outer ridge that matches the inner flange height of most 1/28 scale wheels. The result from this is a tire that is easier to glue (which we recommend) and also more stability to the tire in the case you prefer to use tape. Made from durable and tough glass reinforced nylon, these wheels are acetone safe so they can be re-used.The Taller aspect of the wheel makes the sidewall effectively smaller in order to also aid in the increase of corner speed.
All new from Reflex Racing is the Speed Dish Line of wheels. Designed with performance and durability in mind, these molded wheels have a 0.5mm outer ridge that matches the inner flange height of most 1/28 scale wheels. The result from this is a tire that is easier to glue (which we recommend) and also more stability to the tire in the case you prefer to use tape. Made from durable and tough glass reinforced nylon, these wheels are acetone safe so they can be re-used.The Taller aspect of the wheel makes the sidewall effectively smaller in order to also aid in the increase of corner speed.
All new from Reflex Racing is the Speed Dish Line of wheels. Designed with performance and durability in mind, these molded wheels have a 0.5mm outer ridge that matches the inner flange height of most 1/28 scale wheels. The result from this is a tire that is easier to glue (which we recommend) and also more stability to the tire in the case you prefer to use tape. Made from durable and tough glass reinforced nylon, these wheels are acetone safe so they can be re-used.The Taller aspect of the wheel makes the sidewall effectively smaller in order to also aid in the increase of corner speed.
All new from Reflex Racing is the Speed Dish Line of wheels. Designed with performance and durability in mind, these molded wheels have a 0.5mm outer ridge that matches the inner flange height of most 1/28 scale wheels. The result from this is a tire that is easier to glue (which we recommend) and also more stability to the tire in the case you prefer to use tape. Made from durable and tough glass reinforced nylon, these wheels are acetone safe so they can be re-used.The Taller aspect of the wheel makes the sidewall effectively smaller in order to also aid in the increase of corner speed.
All new from Reflex Racing is the Speed Dish Line of wheels. Designed with performance and durability in mind, these molded wheels have a 0.5mm outer ridge that matches the inner flange height of most 1/28 scale wheels. The result from this is a tire that is easier to glue (which we recommend) and also more stability to the tire in the case you prefer to use tape. Made from durable and tough glass reinforced nylon, these wheels are acetone safe so they can be re-used.The Taller aspect of the wheel makes the sidewall effectively smaller in order to also aid in the increase of corner speed.
All new from Reflex Racing is the Speed Dish Line of wheels. Designed with performance and durability in mind, these molded wheels have a 0.5mm outer ridge that matches the inner flange height of most 1/28 scale wheels. The result from this is a tire that is easier to glue (which we recommend) and also more stability to the tire in the case you prefer to use tape. Made from durable and tough glass reinforced nylon, these wheels are acetone safe so they can be re-used.The Taller aspect of the wheel makes the sidewall effectively smaller in order to also aid in the increase of corner speed.
All new from Reflex Racing is the Speed Dish Line of wheels. Designed with performance and durability in mind, these molded wheels have a 0.5mm outer ridge that matches the inner flange height of most 1/28 scale wheels. The result from this is a tire that is easier to glue (which we recommend) and also more stability to the tire in the case you prefer to use tape. Made from durable and tough glass reinforced nylon, these wheels are acetone safe so they can be re-used.The Taller aspect of the wheel makes the sidewall effectively smaller in order to also aid in the increase of corner speed.
All new from Reflex Racing is the Speed Dish Line of wheels. Designed with performance and durability in mind, these molded wheels have a 0.5mm outer ridge that matches the inner flange height of most 1/28 scale wheels. The result from this is a tire that is easier to glue (which we recommend) and also more stability to the tire in the case you prefer to use tape. Made from durable and tough glass reinforced nylon, these wheels are acetone safe so they can be re-used.The Taller aspect of the wheel makes the sidewall effectively smaller in order to also aid in the increase of corner speed.
