This charging cable was designed to be used with XT60 output chargers to be used with our hard case battery packs. Durable, stylish and perfect length cables to help you tidy up your pit space!
These custom made 2mm split plugs by Reflex Racing are designed to be tougher and have less IR than other plugs available in the market. These plugs are manufactured to our strict specification, in order to solder better and have tougher soldering connections going to your battery, since the wires we use in 1/28 can be a bit fragile. In our signature, attention to detail style, we made a ridge on the top of the plug to make it easier to pull on a surface without having to yank on the wire.
1 Stecker-Set,Passend um die Standard Stecker von Lipos, Ladekabel und ESC zu ersetzen.
Extrem tiefer Übergangswiderstand für möglichst geringen Verlust. Extra satter Sitz, damit die Steckverbindung sich beim Fahren oder bei einem Crash nicht löst.
Inhalt:
1 x Stecker, 1 x Buchse aus CNC gefrästem Kunststoff
Kupfer pins und stainless steel Schrauben
6 Silikon Kabel (22awg)
Features:
Der Stecker ist bis 30A geeignet
Extra satter Sitz der Steckverbinder
Sehr einfach zu löten dank grosser Lötlaschen
XT60 auf PH2.0 Stecker Ladekabel. Geeignet zum Laden und Entladen von einem 2S-Lipo mit PH2.0-Anschluss (GL Racing, PN Racing, Marka Lipos). Hinweis:Diese Kabel sind nicht für das Laden höher als 2A empfohlen!- Hochwertiger Silikondraht 24AWG - Kabellänge: 16cm
4mm Bananenstecker/XT60 auf PH2.0 Stecker Ladekabel. Geeignet zum Laden und Entladen von einem 2S-Lipo mit PH2.0-Anschluss (GL Racing, PN Racing, Marka Lipos). Hinweis:Diese Kabel sind nicht für das Laden höher als 2A empfohlen!- Hochwertiger Silikondraht 24AWG - Kabellänge: 16cm
This charging cable was designed to be used with XT60 output chargers to be used with our hard case battery packs. Durable, stylish and perfect length cables to help you tidy up your pit space!
This cable design for Ultra Power UP-S4AC ChargerCharging 1S Li-Po Battery Molex Plug#700380#700430#700444Attention needs to connect the Black/Red plug first, then connect the Blue/Red plug.
These custom made 2mm split plugs by Reflex Racing are designed to be tougher and have less IR than other plugs available in the market. These plugs are manufactured to our strict specification, in order to solder better and have tougher soldering connections going to your battery, since the wires we use in 1/28 can be a bit fragile. In our signature, attention to detail style, we made a ridge on the top of the plug to make it easier to pull on a surface without having to yank on the wire.
3x JST-PH Parallel charging cable
For GLA and Atomic AMZ/BZ Lipo batteries or any other 2S Lipo with a JST-PH connector.
This handy charge cable allows you to connect 4mm banana plugs to chargers, and the charger's balance board.
On the battery side, we have provided 3x JST-PH connectors so that you can charge/discharge up to 3 packs at a time.
You do not have to use all 3 of course, using it to charge 1 pack is perfectly fine, but if you would like charge/discharge up to 3 packs together, this cable can do it.
For those new to parallel charging, you can google/you tube information on it, but in summary:
You can only connect 2S Lipo to this cable
Mixing 300mAh, 330mAh, 360mAh together is ok
The packs should be reasonably similar in voltage, for example, 2 packs 90% full, 1 pack empty, is NOT such a good idea, as it will cause a lot of current(Amps) going from the full packs to the empty pack, charging the empty pack at very high current(AMps), this might even melt the cable if the Packs are large/high C enough.
All empty is fine, ~30%, ~40%, ~50% mix together is fine.
Ideally charger capacity set to total mAh of the packs
Charger current can scale up according to total capacity of the packs
Below is a good video guide:
https://www.youtube.com/watch?v=WY194Md6KNg
Produktinformationen "3x GL connector Parallel Charging Cable"
[PT0006] 3x GL connector Parallel Charging Cable
Details:
3x JST-PH Parallel charging cable
For GLA and Atomic AMZ/BZ Lipo batteries or any other 2S Lipo with a JST-PH connector.
This handy charge cable allows you to connect 4mm banana plugs to chargers, and the charger's balance board.
On the battery side, we have provided 3x JST-PH connectors so that you can charge/discharge up to 3 packs at a time.
You do not have to use all 3 of course, using it to charge 1 pack is perfectly fine, but if you would like charge/discharge up to 3 packs together, this cable can do it.
For those new to parallel charging, you can google/you tube information on it, but in summary:
You can only connect 2S Lipo to this cable
Mixing 300mAh, 330mAh, 360mAh together is ok
The packs should be reasonably similar in voltage, for example, 2 packs 90% full, 1 pack empty, is NOT such a good idea, as it will cause a lot of current(Amps) going from the full packs to the empty pack, charging the empty pack at very high current(AMps), this might even melt the cable if the Packs are large/high C enough.
All empty is fine, ~30%, ~40%, ~50% mix together is fine.
Ideally charger capacity set to total mAh of the packs
Charger current can scale up according to total capacity of the packs
Receiver Cable (RX cable)
Compatible with Swave-E2 & Swave-W & W2 ONLY
Cannot use on Swave-E
1.0mm JST to 1.5mm JST
Wire length: 80mm
** Some aftermarket / no-brand receiver may require swap the cable you will need to consult your receiver seller.
Marka
Racing safety lipo bag for charging and storage LiPo batteries.
Made from
fire-proof and fire-resistant material.The bag is
in black color and carries the Marka logo.You can
store two standard size batteries.
For GLA, Atomic AMZ/BZ and Jomurema Lipo batteries or any other 2S Lipo with a JST-PH connector.This handy charge cable allows you to connect XT60 plug to chargers, and the charger's balance board.On the battery side, we have provided 3 x JST-PH connectors so that you can charge/discharge up to 3 packs at the same time.Charge one battery is fine, if you charge 3 batteries together, make sure all batteries is same type and capacity.Total length 18cm, protected by PE wrapHigh quality Silicon wire 14AWG for power, 22AWG for Balance Plug
Adapterkabel für das Ladegerät Ultra Power UP-S4AC um die üblichen 2S 7.4V Lipos von GL Racing / Marka / PN Racing mit JST-PH 2.0 Stecker zu laden.Adapterkabel:XH (3 Pin Buchse) zu JST PH 2.0 (3 Pin Stecker)
