New geometry for 2023!
the shock is now located more forward for a more linear feel and increased grip.also battery compartment is wider to accommodate some of the new larger batteries.you can remove the battery without removing the shock now
PLEASE WATCH THE INSTALL BEFORE ATTEMPTING THE INSTALLATIONWatch Video
High Quality Double Shield Ceramic Bearing Set for your 1/28th scale car with 3mm front axles.These bearings have very low axial play and spin super free.
Die Version 2 der beliebten Front Achsen mit Innengewinde. Jetzt aus Titanium für mehr Haltbarkeit. Die V2 Achsen ermöglichen es, den vorderen Offset um 1mm Spurweite in Schritten von 0,5 mm durch die mitgelieferten M3x0,5 mm Axle Shims anzupassen. Die Achsen mit umgekehrtem Gewinde sind kompatibel mit dem Reflex Racing RX28 und auch GL Racing oder RTRC Fahrzeugen. Durch die Umkehrung des Gewindes und die Verwendung einer Schraube anstelle einer Mutter, ist es weniger wahrscheinlich, dass sich die Frontpartie Ihres Fahrzeugs in den RCP-Schienen verfängt, wenn Sie Räder mit geringerem Offset fahren. Das Kit wird mit 2 Achsen, 4 Stück M3x0,5 Kupferscheiben und 2 Stück M2x4mm Kopfschrauben geliefert. Tipp! Abhängig vom verwendeten Radtyp kann es vorkommen, dass die Achsen ein wenig axiales Spiel haben (minimal). Sie können dies durch leichtes Abschleifen der äußeren Achse beheben, um sie etwas schmaler zu machen. *****************************This is the V2 of our reverse axles. Now made from Titamium for more durability. The V2 axles allow you to adjust your front offset 1mm of trackwidth in increments of 0.5mm though the included M3x0.5mm Axle Shims. Reverse thread axles compatible with your Reflex Racing RX28 and GL/Atomic cars. By reversing the thread and using a screw instead of a nut, the front end of your car is less likely to snag into the RCP rails when running lower offset wheels. The kit comes with 2 Axles, 4pcs of M3x0.5 Copper Shims and 2pcs of M2x4mm button head screws. Tip: Depending on the type of wheel you use, sometimes, the axles can have a little bit of axial side to side play (minimal). You can tighten this up by lightly sanding the outer axle to make is slightly narrower.
This is the all new GL RGT Rear Geometry Conversion Kit.Developed in house this kit was designed with our numerous years of experience designing 1/12 and 1/10 Pan Cars.The shock mounting postions and angles have been revised, the center of gravity has been dropped and the parts count and complexity have been reduced considerably. Additionally the integrated rear body mount position is compatible with most lexan bodies we have tested. The results are a car that produces more rear grip, better steering and more consistent, predictable handling. Having removed the motor mount shock mount extension also allows for easier wire routing for smoother pod movement and better airflow for the motor to stay cool.Lap time wise we have seen resonable improvement, and consistency has gone through the roof! The car is much more composed under power and tracks far straighter. As another benefit, the time in between rear damper maintenance has been increased.This kit includes the rear cross brace the aluminum tri mount to be installed on the stock motor mount. It is compatible with both the GL GLR rear shocks and PN Racing Side Shocks.
Needed to Complete:-When using GLR Parts:*GLR-S005 Plastic Shocks*GLR-S016 Alloy Adjusters*GLR-S021 Pivot Balls*2 x M2 x 4mm BH Screws*2 x M2 x 6mm Set Screws*GLR-003-S Spring Set(*alternatively, using Atomic 3.5mm Ball Studs simplifies the parts count AMZ-OP023, use 4 pcs of these plus 2x M2 nuts)
-When Using PN Racing Parts*MR2162A Spring Set*MR2990*4 x M2 x 8mm BH Machine Screws*2 x M2 Nut