You will get a 20cm long red color + 20cm long black color 22AWG silicone cable Cable Specification:
Material: Soft Silicone
O/D: 1.70mm
Strand Count: 60
Strand Diameter: 0.08 mm Package Included:
1 x 20cm red color silicone cable
1 x 20cm black color silicone cable
Made with flexible Silicone Sheathing, this ESC to receive link wire is more easily coiled, routed and shorter than std wires usually supplied with electronics. Up your wiring game and use this all black wire for the stealth look! This set comes with 1 wire. ESC Side plug is not installed. You must match the wire order to the oem wire supplied with your electronics.
Sensorkabel passend für ESC:- GL-SD-ESC-010T
- GL-SD-ESC-020T
- GL-SD-ESC-030T- Hobbywing Mini28für GL Motoren mit dem neuen, kleinen Sensorkabelanschluss
Produktinformationen "3x GL connector Parallel Charging Cable"
[PT0006] 3x GL connector Parallel Charging Cable
Details:
3x JST-PH Parallel charging cable
For GLA and Atomic AMZ/BZ Lipo batteries or any other 2S Lipo with a JST-PH connector.
This handy charge cable allows you to connect 4mm banana plugs to chargers, and the charger's balance board.
On the battery side, we have provided 3x JST-PH connectors so that you can charge/discharge up to 3 packs at a time.
You do not have to use all 3 of course, using it to charge 1 pack is perfectly fine, but if you would like charge/discharge up to 3 packs together, this cable can do it.
For those new to parallel charging, you can google/you tube information on it, but in summary:
You can only connect 2S Lipo to this cable
Mixing 300mAh, 330mAh, 360mAh together is ok
The packs should be reasonably similar in voltage, for example, 2 packs 90% full, 1 pack empty, is NOT such a good idea, as it will cause a lot of current(Amps) going from the full packs to the empty pack, charging the empty pack at very high current(AMps), this might even melt the cable if the Packs are large/high C enough.
All empty is fine, ~30%, ~40%, ~50% mix together is fine.
Ideally charger capacity set to total mAh of the packs
Charger current can scale up according to total capacity of the packs
3x JST-PH Parallel charging cable
For GLA and Atomic AMZ/BZ Lipo batteries or any other 2S Lipo with a JST-PH connector.
This handy charge cable allows you to connect 4mm banana plugs to chargers, and the charger's balance board.
On the battery side, we have provided 3x JST-PH connectors so that you can charge/discharge up to 3 packs at a time.
You do not have to use all 3 of course, using it to charge 1 pack is perfectly fine, but if you would like charge/discharge up to 3 packs together, this cable can do it.
For those new to parallel charging, you can google/you tube information on it, but in summary:
You can only connect 2S Lipo to this cable
Mixing 300mAh, 330mAh, 360mAh together is ok
The packs should be reasonably similar in voltage, for example, 2 packs 90% full, 1 pack empty, is NOT such a good idea, as it will cause a lot of current(Amps) going from the full packs to the empty pack, charging the empty pack at very high current(AMps), this might even melt the cable if the Packs are large/high C enough.
All empty is fine, ~30%, ~40%, ~50% mix together is fine.
Ideally charger capacity set to total mAh of the packs
Charger current can scale up according to total capacity of the packs
Below is a good video guide:
https://www.youtube.com/watch?v=WY194Md6KNg
Made with flexible Silicone Sheathing, this ESC to receive link wire is more easily coiled, routed and shorter than std wires usually supplied with electronics. Up your wiring game and use this all black wire for the stealth look! This set comes with 5 wires. ESC Side plug is not installed. You must match the wire order to the oem wire supplied with your electronics.
Receiver Cable (RX cable)
Compatible with Swave-E2 & Swave-W & W2 ONLY
Cannot use on Swave-E
1.0mm JST to 1.5mm JST
Wire length: 80mm
** Some aftermarket / no-brand receiver may require swap the cable you will need to consult your receiver seller.
For Swave-E2 / Swave-W & W2 ONLY
Cannot use on Swave-E
Suitable for Ensotech & Aurora Motor
Cable Stocket: Motor end 5 pin / ESC end 5 pin
Color: Black
Wire length: 90mm
For GLA, Atomic AMZ/BZ and Jomurema Lipo batteries or any other 2S Lipo with a JST-PH connector.This handy charge cable allows you to connect XT60 plug to chargers, and the charger's balance board.On the battery side, we have provided 3 x JST-PH connectors so that you can charge/discharge up to 3 packs at the same time.Charge one battery is fine, if you charge 3 batteries together, make sure all batteries is same type and capacity.Total length 18cm, protected by PE wrapHigh quality Silicon wire 14AWG for power, 22AWG for Balance Plug
