The Marka Racing Brushless Motor 3500kv have much-more torque and acceleration than others VE motor.
The Marka Motor heatsink can is annodized with black color and the Alu end-bell is annodized in red color.
In this way we tryed to keep Marka brand colors and offer a nice design. SpecificationsScale: 1/28th BrushlessSensorlessRPM: 30000 with 8.4VKV Rating: 3467Kv LiPo/Nimh Cells: 2S or 4xNimh 1.2V (4.8V) No-load Current: 0.2A Timing: Fix Weight: 17.3grAluminium Heatsink Canhas the 15mm diameter same as normal brushed 130 motor.has holes in the front and lateral sides for a good ventilation that allows for a better heat dispersionin the front there are M2 screws holes that allows to fit the motor on all the types of Miniz motor mount and chassis has printed Marka logo on the lateral side and the Kv number to recognize the motor type Stator high quality wires used for high temperature and longevity life high quality wires producing good torque and speed Rotor The rotor has the following size 6.0x14.5mm is the standard one. The rotor is interchangeable and is possible change with other size 6x(11.5mm-12.5mm-13.5mm-15.5mm-16.5mm).
The shaft is 2mm. Bearing JAPAN high quality duel ball Bearing included Compatible Fits in all Kyosho, PN Racing, GL Racing, Atomic, Xpower motor mount.
Fits in all Mini-Z chassis MR02, MR03, F1, AWD, GLR, GLA, GLF, BZ ect. Wire ConnetionFor connect to the ESC use 22AWG/0.35mm silicon wire Screws To mount the motor on the motor mount, use the following screws: On PN Racing motor mount use M2x4mm countersunk screws for aluminum/metal On GL Racing (GLR, GLA e GLF) or Atomic (BZ) motor mount use M2x4mm button screws for aluminum/metal The screws are not included.
For GLA-V2, GLR, GLR-GT, GL-Drift-2022, GLF-1, GL-RIDERArtikelbezeichnung: GL003-DMG
Alternative Artikelnummern: GL-Drift-S-025, GL-GT-S-035, GLF-S-016
Features:
Alloy Top and Bottom Casing
Full Metal gears
Dual Bearing
Speed: 0.06sec/ 60° @ 6.0V
Torque: 1.10 kg . cm @ 6.0V
Weight: 5g
Alu Servohorn inklusive!!***********A06CLS is another streering servo designed for mini z cars and other mini scale models. This servo inherits the advantages of A11CLS servo. Not only did the body to ultra-small size, but the torque go up to 2.2kg-cm. With the help of coreless motor and titanium gear, it will become an indispensable part of mini z cars. Try it and you won't put it down.
Feature- Ultra light weight mini z servo- High accuracy tianium gear- High quality coreless motor- Fast cooling aluminum case- DIY parameter via USB programmer card- Design for mini z cars, 1/18, 1/24, 1/27, 1/28 Scale Cars such as GLR /GLA /GLF-1 /GL-Rider etc.
Specification:- Operating Voltage: 4.8-6.0V- Operating speed: 0.075sec/60°@4.8V- Operating speed: 0.066sec/60°@6.0V- Stall Torque: 1.8 kg-cm (25 oz-in) @4.8V- Stall Torque: 2.2 kg-cm (30 oz-in) @6.0V- Gear: Titanium- Motor: Coreless- Size: 20*8*17.8mm (0.78 x 0.31 x 0.70 in)- Weight: 7g- Connector Wire: JR or JST1.5 60mm for selection /28AWG
AGFrc A06CLS V2 Coreless Titanium Gear 0.052sec 3.0kg-cm Micro Digital Servo for Mini Scale RC CarsHinweis:Spezielle Ausführung mit JST 1.5 Stecker und 20T Spline (20 Zähne) speziell für Mini Z Autos im Massstab 1:28 wie GL Racing GLD, GLA, GLR, GLF-1, GLR GT, RTRC RTA, Reflex Racing RX, Nexx Racing Specter.A06CLS V2 ist die neue Version des beliebten A06CLS Servo und wurde speziell für für MiniZ / 1:28 RC Racer entwickelt. Dieses Servo ist extra klein und bietet trotzdem ein hohes Drehmoment mit bis zu 3.0kg-cm und bis zu einer Geschwindigkeit von 0.055sec bei 8.4V. Dank des zuverlässigen bürstenlosen Motors und des Titan-Getriebes ist die Leistung beachtlich. Es übernimmt die Vorteile des A06CLS-Servos ist neu aber für 2S (max. 8.4V) ausgelegt. Features:- Ultra light weight mini z servo- High accuracy tianium gear- High quality coreless motor- Fast cooling aluminum case- DIY parameter via USB programmer card- Design for mini z cars, 1/18, 1/24, 1/27, 1/28 Scale Cars such as GLR /GLA /GLF-1 /GL-Rider etc.
Specification:- Operating Voltage: 4.8 - 8.4V- Operating speed: 0.075sec/60° @ 4.8V- Operating speed: 0.066sec/60° @ 6.0V- Operating speed: 0.058sec /60° @ 7.4V- Operating speed: 0.052sec /60° @ 8.4V- Stall Torque: 1.8 kg-cm @4.8V- Stall Torque: 2.2 kg-cm @ 6.0V- Stall Torque: 2.6 kg-cm @ 7.4V- Stall Torque: 3.0 kg-cm @ 8.4V- Gear: Titanium- Motor: Coreless- Size: 20*8*17.8mm (0.78 x 0.31 x 0.70 in)- Weight: 7g- Connector Wire: JST1.5 - Spline: 20TLieferung mit Kunststoff-Servohorn!
Ensotech brings the ultimate technology to mini-scale slotless motors and is pleased to introduce their third version in a new matte blue finish Swave-ZM V3 sensored brushless motor for 1:28th scale R/C race.
After a year of research and testing, using a new type of sensor component, a more efficient copper wiring, and magnet to produce Swave-ZM V3 motor under an improved production method. All these updates result in a lowered overall resistance and an improved current flow. In terms of figures, the Swave ZM-V3 motor has increased the overall performance by almost 20%. These versions of motors feel significantly punchier although retaining a smooth powerful acceleration.
Specification:
Motor Type: 3 Phases, Slotless, BrushlessPoles: 2PMotor Shaft Flat Spot: YESPower Cable: 3pcs x 100mm pre-soldered blue color cablesWeight: 21g include motor wire
Package:1 x Ensotech Swave-ZM V3 5500KV motor
Product Type: MX EVO
RX-DSM2
Protocol: DSM/DSM2
Size: 10.0*13.5*3.5mm
Work Volt: 3.0V/3.3V
Reaction Time:
EVO->5.5ms - 4CH PWM->5.5/11ms
Support KYOSHO EVO
Mode (MR-03EVO/MA-03EVO): Yes
Support 4CH PWM OUTPUT
Mode: Yes
Support 1/72-1/64 RC
Car Mode: Yes
Support 1/43-1/24 RC
Car Mode: Yes
FW UPDATE: Yes
Kompatible Spektrum Fernsteuerungen:
DX2EDX3CDX4SDX5CDX5-ProDX5-Rugged
Anleitung
Transponder ID für Robitronic Rundenzeitmesssysteme Grösse: 12 x 16 x 5 mmGewicht: 3gBetriebsspannung: 4.2 - 6 VoltStromverbrauch: 50mA max.Silikonkabel mit JST Stecker passend für Mini-Z und Micro/Nano RX (GL Racing, RTRC, PN Racing,..) mit entsprechendem Stecker
Spare gear set for Graupner DES131 servo.
They don't break that easily, but it can happen, if your DES131 is broken, open it and check if one of the gears is broken, if so, this is what you need to fix it.
For GLA and GLA-V2
Alu Servohorn inklusive!!***********A06CLS is another streering servo designed for mini z cars and other mini scale models. This servo inherits the advantages of A11CLS servo. Not only did the body to ultra-small size, but the torque go up to 2.2kg-cm. With the help of coreless motor and titanium gear, it will become an indispensable part of mini z cars. Try it and you won't put it down.
Feature- Ultra light weight mini z servo- High accuracy tianium gear- High quality coreless motor- Fast cooling aluminum case- DIY parameter via USB programmer card- Design for mini z cars, 1/18, 1/24, 1/27, 1/28 Scale Cars such as GLR /GLA /GLF-1 /GL-Rider etc.
Specification:- Operating Voltage: 4.8-6.0V- Operating speed: 0.075sec/60°@4.8V- Operating speed: 0.066sec/60°@6.0V- Stall Torque: 1.8 kg-cm (25 oz-in) @4.8V- Stall Torque: 2.2 kg-cm (30 oz-in) @6.0V- Gear: Titanium- Motor: Coreless- Size: 20*8*17.8mm (0.78 x 0.31 x 0.70 in)- Weight: 7g- Connector Wire: JR or JST1.5 60mm for selection /28AWG
Motor developed with GLA in mind, enough power for experienced usersMore power - a little more powerful than PN5500, but less than PN7500Easier to control - with a more linear power band making your car easier to control.Longer run time - it also boast higher electrical efficiency than motors of the same classPowerful til the end - Power level stays more consistent towards the end of each run, but this does mean that motor feels hotter at the end of run, because it stayed at high power levels until the very end.Taller gear ratios - recommended GLA gear ratio from 5.4 to 6.1 depending on your driving style and track layoutTIP: Wiring is reverse to PN, so if you are swapping out a PN, swap any 2 of the 3 motor wires
Ensotech brings the ultimate technology to mini-scale slotless motors and is pleased to introduce their third version in a new matte blue finish Swave-ZM V3 sensored brushless motor for 1:28th scale R/C race.
After a year of research and testing, using a new type of sensor component, a more efficient copper wiring, and magnet to produce Swave-ZM V3 motor under an improved production method. All these updates result in a lowered overall resistance and an improved current flow. In terms of figures, the Swave ZM-V3 motor has increased the overall performance by almost 20%. These versions of motors feel significantly punchier although retaining a smooth powerful acceleration.
Specification:
Motor Type: 3 Phases, Slotless, BrushlessPoles: 2PMotor Shaft Flat Spot: YESPower Cable: 3pcs x 100mm pre-soldered blue color cablesWeight: 21g include motor wire
Package:1 x Ensotech Swave-ZM V3 4500KV motor
Easylap Personal IR Transponder Compatible with EasyLap & Robitronic Lap Counter systemSmaller volume Stable quality, low failure rateMulti Connection to 1:28 RC car and 1:10 RC carCan Use for indoor RC (Kyosho 1:28 MiniZ AWD/MR03/MR02/MR01 MiniBuggy etc, Atomic AMZ/AMR/BZ, GL-Racing GLA, GLR, GLR-GT, GLF, GLA-Giulia,...) Feature:
Cable for AMZ/BZ/GLA/SZ Etc (Mini JST Plug) x 1pcs
Receiver Einheit für das Mini-Z Evo Board kompatibel mit der FLYSKY Noble NB4 Fernsteuerung.Technische Daten:Funkfrequenz: 2,4 GHzDrahtloses Protokoll: AFHDS 3Reichweite: > 50m (Boden)Antennentyp: EinzelantenneAbmessungen: 20*14*3,5 mmkompatibel mit Mini-z EVO Board
GL High-Torque Brushless Motor (8600KV)
Motor developed with NiMH Mini-Zs as well as GLA in mind, very high power for expert users
More power - one of the most powerful motors out there, due to its High Torque, KV rating is not high, but more poweful than some higher KV motors on market
Easier to control - with a more linear power band making your car easier to control.
Longer run time - it also boast higher electrical efficiency than motors of the same class
Powerful til the end - Power level stays more consistent towards the end of each run, but this does mean that motor feels hotter at the end of run, because it stayed at high power levels until the very end.
Taller gear ratios - recommended GLA gear ratio from 8.2 to 9.5 depending on your driving style and track layout
TIP: Wiring is reverse to PN, so if you are swapping out a PN, swap any 2 of the 3 motor wires
Flyskys "Noble NB4" ist ein High-End-Sender mit 2,4-GHz-Spezifikationen, das sich ideal für den Aufstieg aus dem Mittelklassesegment eignet. Abgesehen von der hohen Leistung, die für High-End-Sender erforderlich sind, ist das Hauptmerkmal der Noble NB4, dass sie mit einem vollfarbigen Touchpanel-Displays, das alle Funktionen und Einstellungen steuert, ausgestattet ist.
Es ist möglich, umfangreiche Menüs wie Endpunktanpassung, Exponential, ABS, Modellspeicher etc., wie ein Smartphone zu bedienen. Da die verschiedenen Einstellungsbildschirme zudem grafisch gestaltet sind, kann jeder die Einstellungen intuitiv und einfach ändern. Eine weitere neuartige Idee ist eine um 180° drehbare Lenkradhalterung, die ohne Werkzeug für Linkshänder umgestellt werden kann. Darüber hinaus wird ein herausnehmbarer externer Akku verbaut, der auch als mobile Powerbank verwendet werden kann. Die Stromversorgung wird durch den externen Akku und den eingebauten Akku dupliziert. Die Noble NB4 ist eine der fortschrittlichsten Fernsteuerungen für Autos und Boote.
Unterstützt Mini-Z Evo Boards und Mini-Z RWD (mit FHSS FR-Modul FS-RM005
)
Spezifikationen:Artikel Modell: FS-NB4Kanal: 4CHPower: <20dBm(EU)2,4 Ghz Produkt: AFHDS 3Modulation: DSSSKanal Antwort: <13msNiederspannung Alarm: <3,6 VDaten Ausgang: Micro USBAntenne: eingebaut, EinzelantenneBatterie: 3,7 V 4300mAh lipo Batterie (abnehmbar) + built-in batterie!Ladezeit: ca. 2 stundenArbeitszeit: über 8 stundenGröße: 190*129*114mmGewicht: 520gZertifizierung: CE, FCC ID: N4ZFG400, MIC, RCM
Lieferumfang:1 x Fernbedienung Noble NB41 x 3,7 V 4300mAh lipo Batterie1 x USB Kabel1 x Ersatz-Grip Abdeckung1 x Anleitung (englisch)inklusive 1 x FS-MiniZRF3 Empfänger für Mini-Z Evo Board
The Marka Racing Brushless Motor 5500kv have much-more torque and acceleration than others VE motor.
The Marka Motor heatsink can is annodized with black color and the Alu end-bell is annodized in red color.
In this way we tryed to keep Marka brand colors and offer a nice design. SpecificationsScale: 1/28th BrushlessSensorlessRPM: 47000 with 8.4VKV Rating:
5467
Kv LiPo/Nimh Cells: 2S or 4xNimh 1.2V (4.8V) No-load Current: 0.4A Timing: Fix Weight: 17.4grAluminium Heatsink Canhas the 15mm diameter same as normal brushed 130 motor.has holes in the front and lateral sides for a good ventilation that allows for a better heat dispersionin the front there are M2 screws holes that allows to fit the motor on all the types of Miniz motor mount and chassis has printed Marka logo on the lateral side and the Kv number to recognize the motor type Stator high quality wires used for high temperature and longevity life high quality wires producing good torque and speed Rotor The rotor has the following size 6.0x14.5mm is the standard one. The rotor is interchangeable and is possible change with other size 6x(11.5mm-12.5mm-13.5mm-15.5mm-16.5mm).
The shaft is 2mm. Bearing JAPAN high quality duel ball Bearing included Compatible Fits in all Kyosho, PN Racing, GL Racing, Atomic, Xpower motor mount.
Fits in all Mini-Z chassis MR02, MR03, F1, AWD, GLR, GLA, GLF, BZ ect. Wire ConnetionFor connect to the ESC use 22AWG/0.35mm silicon wire Screws To mount the motor on the motor mount, use the following screws: On PN Racing motor mount use M2x4mm countersunk screws for aluminum/metal On GL Racing (GLR, GLA e GLF) or Atomic (BZ) motor mount use M2x4mm button screws for aluminum/metal The screws are not included.
