Reflex Racing
Designed und entwickelt in den USA, bietet Reflex Racing Tuning Teile für 1:28 RC Racer. Mit dem RX28 Chassis bietet Reflex Racing selber ein Top Chassis für ambitionierte Fahrer an.
MWX ZS Axles
14,00 CHF*
Universal Zero Slop axles. Get rid of the gap between the inner bearing ID and the OD of the axle. On some cars this clearance can alter your camber by 1-2 degrees!Will fit MWX, GL, RTA, Atomic, Reflex RX28 and many others Comes with extra o rings MAKE SURE AND USE A DROP OF OIL OR GREASE ON THE O RINGS SO THEY SLIDE ON
MWX-ZS-AXL-33
REFLEX RACING Speed Dish Wheel REAR- 14mm +1 offset (White)
5,50 CHF*
All new from Reflex Racing is the Speed Dish Line of wheels. Designed with performance and durability in mind, these molded wheels have a 0.5mm outer ridge that matches the inner flange height of most 1/28 scale wheels. The result from this is a tire that is easier to glue (which we recommend) and also more stability to the tire in the case you prefer to use tape. Made from durable and tough glass reinforced nylon, these wheels are acetone safe so they can be re-used.The Taller aspect of the wheel makes the sidewall effectively smaller in order to also aid in the increase of corner speed.
The 14mm +1 provides a little more stability than the +0 rear and limits rotation a little bit. The result is typically a little easier to drive car.
RX600R141W
REFLEX RACING Speed Dish Wheel REAR- 14mm +1 offest (Grey)
5,50 CHF*
All new from Reflex Racing is the Speed Dish Line of wheels. Designed with performance and durability in mind, these molded wheels have a 0.5mm outer ridge that matches the inner flange height of most 1/28 scale wheels. The result from this is a tire that is easier to glue (which we recommend) and also more stability to the tire in the case you prefer to use tape. Made from durable and tough glass reinforced nylon, these wheels are acetone safe so they can be re-used.The Taller aspect of the wheel makes the sidewall effectively smaller in order to also aid in the increase of corner speed.
The 14mm +1 provides a little more stability than the +0 rear and limits rotation a little bit.
The result is typically a little easier to drive car.
RX600R141G
REFLEX RACING Speed Dish 11mm Wheel - 1.5 Offset (Yellow)
5,50 CHF*
Offest: -1.5mmAll new from Reflex Racing is the Speed Dish Line of wheels. Designed with performance and durability in mind, these molded wheels have a 0.5mm outer ridge that matches the inner flange height of most 1/28 scale wheels. The result from this is a tire that is easier to glue (which we recommend) and also more stability to the tire in the case you prefer to use tape. Made from durable and tough glass reinforced nylon, these wheels are acetone safe so they can be re-used.The Taller aspect of the wheel makes the sidewall effectively smaller in order to also aid in the increase of corner speed.
RX600R-15Y
REFLEX RACING Speed Dish 11mm Wheel - 1.5 Offset (Grey)
5,50 CHF*
Offest: -1.5mm
All new from Reflex Racing is the Speed Dish Line of wheels. Designed with performance and durability in mind, these molded wheels have a 0.5mm outer ridge that matches the inner flange height of most 1/28 scale wheels. The result from this is a tire that is easier to glue (which we recommend) and also more stability to the tire in the case you prefer to use tape. Made from durable and tough glass reinforced nylon, these wheels are acetone safe so they can be re-used.The Taller aspect of the wheel makes the sidewall effectively smaller in order to also aid in the increase of corner speed.
RX600R-15G
REFLEX RACING Speed Dish 11mm Wheel - 1.5 Offset (White)
5,50 CHF*
Offest: -1.5mm
All new from Reflex Racing is the Speed Dish Line of wheels. Designed with performance and durability in mind, these molded wheels have a 0.5mm outer ridge that matches the inner flange height of most 1/28 scale wheels. The result from this is a tire that is easier to glue (which we recommend) and also more stability to the tire in the case you prefer to use tape. Made from durable and tough glass reinforced nylon, these wheels are acetone safe so they can be re-used.The Taller aspect of the wheel makes the sidewall effectively smaller in order to also aid in the increase of corner speed.
RX600R-15W
Reflex Racing 50mm ESC Connection Wire - Black Silicone Sheating (1 pc.)
3,00 CHF*
Made with flexible Silicone Sheathing, this ESC to receive link wire is more easily coiled, routed and shorter than std wires usually supplied with electronics. Up your wiring game and use this all black wire for the stealth look! This set comes with 1 wire. ESC Side plug is not installed. You must match the wire order to the oem wire supplied with your electronics.
RRE010
Reflex Racing 50mm ESC Connection Wire - Black Silicone Sheating (5 pc.)
12,00 CHF*
Made with flexible Silicone Sheathing, this ESC to receive link wire is more easily coiled, routed and shorter than std wires usually supplied with electronics. Up your wiring game and use this all black wire for the stealth look! This set comes with 5 wires. ESC Side plug is not installed. You must match the wire order to the oem wire supplied with your electronics.
RRE010-5
Reflex Racing Speed Dish Side Wall Plate Set (22.0 - 22.6) - Black
10,00 CHF*
Designed to make your life easier. These plates lock into your favorite Reflex Racing Speed Dish wheels for an increased wheel lip diameter. Having a larger diameter lip on the wheel leads to a smaller side wall aspect ratio on your tire, which very effectively reduces traction roll and steering response on your car. These plates are optimized to be used with "Low Profile" style front tires, which when mounted measure around 23.0mm on our wheels. The plate set comes with 4 different sizes: 22.0, 22.2, 22.4 and 22.6mm. How to use: Start with a 23.0mm Diameter Mounted front tire on a speed dish wheel. (We recommend having glued the tire to the wheel, but you no longer have to add superglue to the sidewall.) Install the 23.6mm plate by pressing the 4 prongs into 4 of the 8 slots on the wheel. Make sure it seats all the way. DRIVE!!!It will still take a few laps or maybe half a run to break in your tires, depending on whether you trued or not, but once they do, the car should drive with really good balance. When you notice the steering start dropping off, or if you simply need more steering, go to the next smaller plate. Rinse and repeat.
RX601B
Reflex Racing Speed Dish Side Wall Plate Set (22.0 - 22.6) - Yellow
10,00 CHF*
Designed to make your life easier. These plates lock into your favorite Reflex Racing Speed Dish wheels for an increased wheel lip diameter. Having a larger diameter lip on the wheel leads to a smaller side wall aspect ratio on your tire, which very effectively reduces traction roll and steering response on your car. These plates are optimized to be used with "Low Profile" style front tires, which when mounted measure around 23.0mm on our wheels. The plate set comes with 4 different sizes: 22.0, 22.2, 22.4 and 22.6mm. How to use: Start with a 23.0mm Diameter Mounted front tire on a speed dish wheel. (We recommend having glued the tire to the wheel, but you no longer have to add superglue to the sidewall.) Install the 23.6mm plate by pressing the 4 prongs into 4 of the 8 slots on the wheel. Make sure it seats all the way. DRIVE!!!It will still take a few laps or maybe half a run to break in your tires, depending on whether you trued or not, but once they do, the car should drive with really good balance. When you notice the steering start dropping off, or if you simply need more steering, go to the next smaller plate. Rinse and repeat.
RX601Y
Reflex Racing Speed Dish Side Wall Plate Set (22.0 - 22.6) - White
10,00 CHF*
Designed to make your life easier. These plates lock into your favorite Reflex Racing Speed Dish wheels for an increased wheel lip diameter. Having a larger diameter lip on the wheel leads to a smaller side wall aspect ratio on your tire, which very effectively reduces traction roll and steering response on your car. These plates are optimized to be used with "Low Profile" style front tires, which when mounted measure around 23.0mm on our wheels. The plate set comes with 4 different sizes: 22.0, 22.2, 22.4 and 22.6mm. How to use: Start with a 23.0mm Diameter Mounted front tire on a speed dish wheel. (We recommend having glued the tire to the wheel, but you no longer have to add superglue to the sidewall.) Install the 23.6mm plate by pressing the 4 prongs into 4 of the 8 slots on the wheel. Make sure it seats all the way. DRIVE!!!It will still take a few laps or maybe half a run to break in your tires, depending on whether you trued or not, but once they do, the car should drive with really good balance. When you notice the steering start dropping off, or if you simply need more steering, go to the next smaller plate. Rinse and repeat.
RX601W
Reflex Racing Speed Dish Side Wall Plate Set (22.0 - 22.6) - Grey
10,00 CHF*
Designed to make your life easier. These plates lock into your favorite Reflex Racing Speed Dish wheels for an increased wheel lip diameter. Having a larger diameter lip on the wheel leads to a smaller side wall aspect ratio on your tire, which very effectively reduces traction roll and steering response on your car. These plates are optimized to be used with "Low Profile" style front tires, which when mounted measure around 23.0mm on our wheels. The plate set comes with 4 different sizes: 22.0, 22.2, 22.4 and 22.6mm. How to use: Start with a 23.0mm Diameter Mounted front tire on a speed dish wheel. (We recommend having glued the tire to the wheel, but you no longer have to add superglue to the sidewall.) Install the 23.6mm plate by pressing the 4 prongs into 4 of the 8 slots on the wheel. Make sure it seats all the way. DRIVE!!!It will still take a few laps or maybe half a run to break in your tires, depending on whether you trued or not, but once they do, the car should drive with really good balance. When you notice the steering start dropping off, or if you simply need more steering, go to the next smaller plate. Rinse and repeat.
RX601G
TAR Abziehwerkzeug für Reflex Speed Dish Side Walls (orange)
4,00 CHF*
Mit diesem Werkzeug von TAR kannst du die Reflex Speed Dish Side Walls mühelos ab der Felge nehmen.Einfach Abziehwerkzeug von hinten in den Felge drücken und die Side Wall ausstossen.Material: 3D printedFarbe: orangeLieferumfang: 1 Stück
TAR_Side_Wall_Tool
Mini-Z Tweak Station
50,00 CHF*
Set your tweak with the Mini-Z Tweak Station. User Guide / ManualVideo
MTS10001
REFLEX RACING Speed Dish Wheel REAR- 14mm +1 offset (Yellow)
5,50 CHF*
All new from Reflex Racing is the Speed Dish Line of wheels. Designed with performance and durability in mind, these molded wheels have a 0.5mm outer ridge that matches the inner flange height of most 1/28 scale wheels. The result from this is a tire that is easier to glue (which we recommend) and also more stability to the tire in the case you prefer to use tape. Made from durable and tough glass reinforced nylon, these wheels are acetone safe so they can be re-used.The Taller aspect of the wheel makes the sidewall effectively smaller in order to also aid in the increase of corner speed.
The 14mm +1 provides a little more stability than the +0 rear and limits rotation a little bit.
The result is typically a little easier to drive car.
RX600R141Y
Tipp
Reflex Racing Machined Aluminium Setup Wheels ( 1 Pair)
19,00 CHF*
All new from Reflex Racing is our precision high speed CNC lathe-turned set up wheels. Made without bearings and a deep dish to make it compatible with all 2WD and AWD cars that use a 3mm Axle. The elimination of the bearings in the wheel make the fit with much tighter tolerances, which allows for a more precise camber setting when being used with our RX28A-31 Camber Gauge.Lieferumfang:- 1 Paar
RX536
Tipp
Reflex Racing RX28 102mm Wheel Base Conversion Kit
60,00 CHF*
The all new 102mm wheelbase conversion kit fits all your flat plate versions of the RX28 release to date. It is designed to allow you to mount 102mm bodies like the Mazda 787B on the car for a more versatile experience (Kiss front end needs slight clearance sanded around upper arm area). The chassis was designed with versatility and light weight in mind. You can now use a larger 24mm battery or move the battery on the chassis forward by 4mm to fine tune your weight bias through the included extra holes on the chassis and battery stop.
The kit includes:
RX28 102mm Hardened Steel Plate Chassis with Light Weight Cuts
4mm Shock Cap Extender post and 1mm shim
Battery Stop Post and Screw
Body Side Clips (Tested on Maxda 787B only so far)
RX28A-34
Reflex Racing Mako GT/X TPU lined Bumper (for PNWC Bumper Rules)
20,00 CHF*
This bumper was developed to be in compliance with the 2024 PNWC Bumper Rules. The new requires there to be a 2mm gap between bumper and body if the bumper is made out of CF. This bumper retains the same shape as the RX528 Mako Bumper, but also has a nested, front TPU liner which satisfies the rule as the leading edge is now made from flexible, rubber like material (albeit, still super rigid).
This bumper is slightly heavier, but not by much. We recommend using CA to attach the bumper more securely to the CF part.
RX541
REFLEX RACING Flat Dish AWD Wheel Front +1.25 - White
5,50 CHF*
Our all new AWD Flat Dish wheel is our first foray into the segment. We wanted to capture the success of our 2WD Speed Dish and apply what we have learned since their release in order to increase performance, reliability and affordability to your AWD wheels. The Front and rear wheels have a slightly different height outer side wall in order to balance the performance of the car better and allow for the use of our Low Profile tires both front and rear without the need for truing under most conditions. We recommend starting with our 40 degree front tire, glued to the wheel with full outer sidewall glue and our Low profile 30degree, 11mm tires in the rear, glued to the wheel.
Much like our 2WD wheels, these are made from Fiber Reinforced Nylon and are Acetone safe so they are not only affordable, but also re-usable. Our favorite thing about the material is that the tires bond MUCH better to the wheel and unglued tires become a thing of the past. This allows us to run much smaller tires on our AWDs, which yields faster acceleration and better corner speed.
These wheels are also compatible with our new RX608 Double Decimal Wheel Plate Set.
***For the Giulia, these make the car right about 79mm wide in the front and 78 in the rear. (Yes, much like 10th scale TC's, you want your front slightly wider on an AWD car for more stability, on power steering and less rolling over). While plates are compatible, most bodies are not wide enough when you install the plates. However, we use such small tires and the front side wall is taller, so most of the time, all that is needed is the front sidewall glue. With the Atomic BZ3, the car ends up at about 75mm front and 74mm rear.
RX607F125W
REFLEX RACING Flat Dish AWD Wheel Front +1.25 - Gray
5,50 CHF*
Our all new AWD Flat Dish wheel is our first foray into the segment. We wanted to capture the success of our 2WD Speed Dish and apply what we have learned since their release in order to increase performance, reliability and affordability to your AWD wheels. The Front and rear wheels have a slightly different height outer side wall in order to balance the performance of the car better and allow for the use of our Low Profile tires both front and rear without the need for truing under most conditions. We recommend starting with our 40 degree front tire, glued to the wheel with full outer sidewall glue and our Low profile 30degree, 11mm tires in the rear, glued to the wheel.
Much like our 2WD wheels, these are made from Fiber Reinforced Nylon and are Acetone safe so they are not only affordable, but also re-usable. Our favorite thing about the material is that the tires bond MUCH better to the wheel and unglued tires become a thing of the past. This allows us to run much smaller tires on our AWDs, which yields faster acceleration and better corner speed.
These wheels are also compatible with our new RX608 Double Decimal Wheel Plate Set.
***For the Giulia, these make the car right about 79mm wide in the front and 78 in the rear. (Yes, much like 10th scale TC's, you want your front slightly wider on an AWD car for more stability, on power steering and less rolling over). While plates are compatible, most bodies are not wide enough when you install the plates. However, we use such small tires and the front side wall is taller, so most of the time, all that is needed is the front sidewall glue. With the Atomic BZ3, the car ends up at about 75mm front and 74mm rear.
RX607F125G
REFLEX RACING Flat Dish AWD Wheel Rear +1.25 - Gray
5,50 CHF*
Our all new AWD Flat Dish wheel is our first foray into the segment. We wanted to capture the success of our 2WD Speed Dish and apply what we have learned since their release in order to increase performance, reliability and affordability to your AWD wheels. The Front and rear wheels have a slightly different height outer side wall in order to balance the performance of the car better and allow for the use of our Low Profile tires both front and rear without the need for truing under most conditions. We recommend starting with our 40 degree front tire, glued to the wheel with full outer sidewall glue and our Low profile 30degree, 11mm tires in the rear, glued to the wheel.
Much like our 2WD wheels, these are made from Fiber Reinforced Nylon and are Acetone safe so they are not only affordable, but also re-usable. Our favorite thing about the material is that the tires bond MUCH better to the wheel and unglued tires become a thing of the past. This allows us to run much smaller tires on our AWDs, which yields faster acceleration and better corner speed.
These wheels are also compatible with our new RX608 Double Decimal Wheel Plate Set.
***For the Giulia, these make the car right about 79mm wide in the front and 78 in the rear. (Yes, much like 10th scale TC's, you want your front slightly wider on an AWD car for more stability, on power steering and less rolling over). While plates are compatible, most bodies are not wide enough when you install the plates. However, we use such small tires and the front side wall is taller, so most of the time, all that is needed is the front sidewall glue. With the Atomic BZ3, the car ends up at about 75mm front and 74mm rear.
RX607R125G
REFLEX RACING Flat Dish AWD Wheel Rear +1.25 - White
5,50 CHF*
Our all new AWD Flat Dish wheel is our first foray into the segment. We wanted to capture the success of our 2WD Speed Dish and apply what we have learned since their release in order to increase performance, reliability and affordability to your AWD wheels. The Front and rear wheels have a slightly different height outer side wall in order to balance the performance of the car better and allow for the use of our Low Profile tires both front and rear without the need for truing under most conditions. We recommend starting with our 40 degree front tire, glued to the wheel with full outer sidewall glue and our Low profile 30degree, 11mm tires in the rear, glued to the wheel.
Much like our 2WD wheels, these are made from Fiber Reinforced Nylon and are Acetone safe so they are not only affordable, but also re-usable. Our favorite thing about the material is that the tires bond MUCH better to the wheel and unglued tires become a thing of the past. This allows us to run much smaller tires on our AWDs, which yields faster acceleration and better corner speed.
These wheels are also compatible with our new RX608 Double Decimal Wheel Plate Set.
***For the Giulia, these make the car right about 79mm wide in the front and 78 in the rear. (Yes, much like 10th scale TC's, you want your front slightly wider on an AWD car for more stability, on power steering and less rolling over). While plates are compatible, most bodies are not wide enough when you install the plates. However, we use such small tires and the front side wall is taller, so most of the time, all that is needed is the front sidewall glue. With the Atomic BZ3, the car ends up at about 75mm front and 74mm rear.
RX607R125W
Reflex Racing Speed Dish Plate Popper - Aluminium
13,50 CHF*
Easily remove the side wall plates from your Reflex Racing Speed Dish Wheels with this cool popper. To remove the plate, place the wheels centered on the popper with the 4 prongs contacting the clips from the plates. Use something like the back of a sharpie pen to push down. This will unlock the plate and allow you to remove it easily.Material: Aluminium
RX606
Reflex Racing RX28G2 Aluminium Front Bulkhead
30,00 CHF*
Gen 2 Bulkhead. No Caster Adjustment. Much tighter tolerances.
RX28-020
Tipp
Reflex Racing RX28SE Worlds Edition 1/28th Scale 2WD Chassis Kit - Gen 2
525,00 CHF*
The RX28SE Worlds Edition kits are here!This kit is basically a replica of the chassis that the team ran in Paris at the 2024 PNWC. It has all the refinements of the Champions edition, plus the new 24mm battery compatible chassis included. Much like the Champions edition, this is not a revolution, but rather an evolution of quality and attention to details that we have meticulously worked on getting ironed out over the last year since the release of the Gen 2 cars. Better tolerances, higher quality finishes, hard coated everything and extra attention to details to make the RX28 experience just a little bit better than before. The Worlds cars build on the great Gen 2 platforms and include all the refinements we have been working so hard at getting to you.
New on the Worlds Edition:RX28SE-08 24mm Battery Compatible ChassisAnd of course all the improvements from the Champions Edition:
Updated chassis with holes for screw on weights
New Body Adjustable Body Post System (adjust body in 1mm increments)
Revised motor mount with locating spline for tougher assembly and less flex,
Updated Axle Carrier to include location for attaching rear mass damper.
Reflex Racing 30 Degree Rear Radial 11mm and 14mm Tires and 40 degree 8.5 and 11mm low profile slicks.
New Aluminum Main Damper with locking adjustment collar.
Updated Front Shock Adjustment collars with laser engraved pre-load dial mark
New Version 4 Ball Differential with Plastic Spur Gear Covers
Updated hard-coated 7075 T6 aluminum pivots and damper pistons
PLUS (all the items that had been Gen 2 running changes):
New Damper Tubes
New Ball Cups and Turnbuckles
30g Stainless Steel Chassis with Hard Coating for more durability, quality and performance vs brass
All New Ultra Low CG Motor Mount for increased corner speed, lighter weight and more precise ride height adjustment. It allows virtually any motor in the industry to be a drop in to the mounting position. Allows gear adjustment from 9T-17T Pinions.
Revised hardware throughout.
Reflex Racing Speed Wheels Included
Dimensions:
98mm Wheelbase
145g-170g weight RTR Depending on body and Electronics
69mm to 78mm Rear Track Width
72mm to 75mm Front Track Width
Need to Complete:
Body and either front clip or front bumper
Wheels and Tires
Electronics: Motor, Lipo Battery, ESC, Receiver and Servo (Please note, the provided servo horn is designed to work with Servo with 20T Spline. (AGFC A06CLS V2, GL, OMG, MWX, PN Anima works fine)
*** ELECTRONICS ARE NOT INCLUDED!!! ***
*** Gear Diff not included ***
IMAGES ARE PRODUCTION SAMPLES - Some Features are not visible.
***********************************************************
Assembly Manual / Montageanleitung:
RX28SE Gen2 Manual
RX28SE-KIT-WE
Tipp
Reflex Racing RX28D Worlds Edition 1/28th Scale 2WD Chassis Kit - Gen 2
375,00 CHF*
The RX28D Worlds Edition kits are here! This kit is basically a replica of the chassis that the team ran in Paris at the 2024 PNWC. It has all the refinements of the Champions edition, plus the new 24mm battery compatible chassis included. Much like the Champions edition, this is not a revolution, but rather an evolution of quality and attention to details that we have meticulously worked on getting ironed out over the last year since the release of the Gen 2 cars. Better tolerances, higher quality finishes, hard coated everything and extra attention to details to make the RX28 experience just a little bit better than before. The Worlds cars build on the great Gen 2 platforms and include all the refinements we have been working so hard at getting to you.
In and effort to more easily identify it, we are now going to call the double a-arm RX28 the "RX28D".
New on the Worlds Edition: RX28A-39 24mm Battery Compatible Steel Chassis
And of course all the improvements from the Champions Edition:
Revised motor mount with locating spline for tougher assembly and less flex.
Updated Axle Carrier to include location for attaching rear mass damper.
Reflex Racing 30 Degree Rear Radial 11mm Tires and 40 degree front low profile slicks.
New Aluminum Main Damper with locking adjustment collar.
Updated Front Shock Adjustment collars with laser engraved pre-load dial mark
New Version 4 Ball Differential with Plastic Spur Gear Covers
Updated hard-coated 7075 T6 aluminum pivots and damper pistons
PLUS (all the items that had been Gen 2 running changes):
New Damper Tubes
New Ball Cups and Turnbuckles
30g Stainless Steel Chassis with Hard Coating for more durability, quality and performance vs brass
All New Ultra Low CG Motor Mount for increased corner speed, lighter weight and more precise ride height adjustment. It allows virtually any motor in the industry to be a drop in to the mounting position. Allows gear adjustment from 9T-17T Pinions.
Revised hardware throughout.
Reflex Racing Speed Wheels Included
Dimensions:
98mm Wheelbase
145g-170g weight RTR Depending on body and Electronics
69mm to 78mm Rear Track Width
72mm to 75mm Front Track Width
Need to Complete:
Body and either front clip or front bumper
Wheels and Tires
Electronics: Motor, Lipo Battery, ESC, Receiver and Servo (Please note, the provided servo horn is designed to work with Servos with 20T Spline. (AGFC A06CLS V2, GL, OMG, PN Anima and MWX will fit well).
**** Electronics are not included ******** Gear Diff not included ****Assembly Manual / Montaganleitung:RX28D G2 Standard
RX28D-KIT-WE
Tipp
Reflex Racing RX28K Worlds Edition 1/28th Scale 2WD Chassis Kit - Gen 2
375,00 CHF*
The RX28K Worlds Edition kits are here! This kit is basically a replica of the chassis that the team ran in Paris at the 2024 PNWC. It has all the refinements of the Champions edition, plus the new 24mm battery compatible chassis included. Much like the Champions edition, this is not a revolution, but rather an evolution of quality and attention to details that we have meticulously worked on getting ironed out over the last year since the release of the Gen 2 cars. Better tolerances, higher quality finishes, hard coated everything and extra attention to details to make the RX28 experience just a little bit better than before.The Worlds Edition cars build on the great Gen 2 platforms and include all the refinements we have been working so hard at getting to you.
New on the Worlds Edition:
RX28A-39 24mm Battery Compatible Steel Chassis
And of course all the improvements from the Gen 2 Champions Edition
Revised motor mount with locating spline for tougher assembly and less flex,
Updated Axle Carrier to include location for attaching rear mass damper.
Reflex Racing 30 Degree Rear Radial 11mm Tires and 40 degree front low profile slicks.
New Aluminum Main Damper with locking adjustment collar.
Updated Front Shock Adjustment collars with laser engraved pre-load dial mark
New Version 4 Ball Differential with Plastic Spur Gear Covers
Updated hard-coated 7075 T6 aluminum pivots and damper pistons
PLUS (all the items that had been Gen 2 running changes):
New Damper Tubes
New Ball Cups and Turnbuckles
30g Stainless Steel Chassis with Hard Coating for more durability, quality and performance vs brass
All New Ultra Low CG Motor Mount for increased corner speed, lighter weight and more precise ride height adjustment. It allows virtually any motor in the industry to be a drop in to the mounting position. Allows gear adjustment from 9T-17T Pinions.
Revised hardware throughout.
Reflex Racing Speed Wheels Included
Dimensions:
98mm Wheelbase
145g-170g weight RTR Depending on body and Electronics
69mm to 78mm Rear Track Width
72mm to 75mm Front Track Width
Need to Complete:
Body and either front clip or front bumper
Wheels and Tires
Electronics: Motor, Lipo Battery, ESC, Receiver and Servo (Please note, the provided servo horn is designed to work with Servos with 20T Spline. (AGFC A06CLS V2, GL, OMG, PN Anima and MWX will fit well).
*** Electronics are not included ****** Gear Diff not included ***Assembly Manual / Montaganleitung:RX28D G2 Standard
RX28K-KIT-WE
REFLEX RACING Flat Dish AWD Wheel Rear +1.25 - Yellow
5,50 CHF*
Our all new AWD Flat Dish wheel is our first foray into the segment. We wanted to capture the success of our 2WD Speed Dish and apply what we have learned since their release in order to increase performance, reliability and affordability to your AWD wheels. The Front and rear wheels have a slightly different height outer side wall in order to balance the performance of the car better and allow for the use of our Low Profile tires both front and rear without the need for truing under most conditions. We recommend starting with our 40 degree front tire, glued to the wheel with full outer sidewall glue and our Low profile 30degree, 11mm tires in the rear, glued to the wheel.
Much like our 2WD wheels, these are made from Fiber Reinforced Nylon and are Acetone safe so they are not only affordable, but also re-usable. Our favorite thing about the material is that the tires bond MUCH better to the wheel and unglued tires become a thing of the past. This allows us to run much smaller tires on our AWDs, which yields faster acceleration and better corner speed.
These wheels are also compatible with our new RX608 Double Decimal Wheel Plate Set.
***For the Giulia, these make the car right about 79mm wide in the front and 78 in the rear. (Yes, much like 10th scale TC's, you want your front slightly wider on an AWD car for more stability, on power steering and less rolling over). While plates are compatible, most bodies are not wide enough when you install the plates. However, we use such small tires and the front side wall is taller, so most of the time, all that is needed is the front sidewall glue. With the Atomic BZ3, the car ends up at about 75mm front and 74mm rear.
RX607R125Y
REFLEX RACING Flat Dish AWD Wheel Front +1.25 - Yellow
5,50 CHF*
Our all new AWD Flat Dish wheel is our first foray into the segment. We wanted to capture the success of our 2WD Speed Dish and apply what we have learned since their release in order to increase performance, reliability and affordability to your AWD wheels. The Front and rear wheels have a slightly different height outer side wall in order to balance the performance of the car better and allow for the use of our Low Profile tires both front and rear without the need for truing under most conditions. We recommend starting with our 40 degree front tire, glued to the wheel with full outer sidewall glue and our Low profile 30degree, 11mm tires in the rear, glued to the wheel.
Much like our 2WD wheels, these are made from Fiber Reinforced Nylon and are Acetone safe so they are not only affordable, but also re-usable. Our favorite thing about the material is that the tires bond MUCH better to the wheel and unglued tires become a thing of the past. This allows us to run much smaller tires on our AWDs, which yields faster acceleration and better corner speed.
These wheels are also compatible with our new RX608 Double Decimal Wheel Plate Set.
***For the Giulia, these make the car right about 79mm wide in the front and 78 in the rear. (Yes, much like 10th scale TC's, you want your front slightly wider on an AWD car for more stability, on power steering and less rolling over). While plates are compatible, most bodies are not wide enough when you install the plates. However, we use such small tires and the front side wall is taller, so most of the time, all that is needed is the front sidewall glue. With the Atomic BZ3, the car ends up at about 75mm front and 74mm rear.
RX607F125Y
Tipp
Reflex Racing Racing 1/28 Set Up Station (incl. Etui)
87,50 CHF*
Dieses Gerät von Reflex ist nicht einfach ein Nachbau chinesischer Setup Stations, sondern wurde von gröseren Einstellgeräten inspiriert. Die Einstellstation wurde entwickelt, um entweder 22,8mm oder 22,5 mm Reifendurchmesser zu simulieren, um eine maximale Einstellgenauigkeit zu erreichen. Optimiert, um entweder 2WD oder AWD spezifische Exzenter zu verwenden. Präzise gefertigt und massgeschneiderte Lager, um das Spiel in der Montag zu minimieren um genauere Messungen zu ermöglichen.Die Setup Station wird in einem praktischem Etui geliefert.
RX547
Reflex Racing RX28 Short Steering Horn (20T)
18,50 CHF*
Dieses kurze Lenkhorn wurde für Anwendungen mit hoher Traktion entwickelt, bei denen Dein Auto zu kantig ist und Du ein langsameres Lenkgefühl wünschst. Es ist ideal für Pan Car und grössere fliessende Rennstrecken, wo Du nicht so viel Lenkung benötigst und wo du normalerweise weniger als 85% Dual Rate fährst.
RX28A-41
Reflex Racing RX28 Linear Steering Horn (20T)
18,50 CHF*
Dieses Servo Horn bietet eine linearere Lenkgeometrie für Deinen RX28. Durch die Verschiebung der Drehpunkte des Servohorns nach vorne, erreichen wir einen höheren Winkel auf die Links, die weniger Ackerman-Effekt auf Ihre Vorderreifen erstellt. Das Ergebnis ist ein Lenkgefühl, das weniger exponentiell ist, wenn die Dual Rate erhöht wird. So kannst Du bei hoher Traktion weniger Lenkeinschlag haben oder bei engen Strecken mit 180ern, wo mehr Lenkeinschlag erforderlich ist, aggressiver fahren.
RX28A-40
Reflex Racing Speed Dish Side Wall Plate Set (22.4 - 23.0) - Black
10,00 CHF*
****This new plate set is slightly oversized from the nominal numbers. Expect them to be about 0.1mm larger than the nominal molded number. This makes this a larger plate set for those that don't want to true their tires at all. Just start with LP Mounted tires and the largest plate and adjust from there!**** Designed to make your life easier. These plates lock into your favorite Reflex Racing Speed Dish wheels for an increased wheel lip diameter. Having a larger diameter lip on the wheel leads to a smaller side wall aspect ratio on your tire, which very effectively reduces traction roll and steering response on your car. These plates are optimized to be used with "Low Profile" style front tires, which when mounted measure around 23.2mm on our wheels. The plate set comes with 4 different sizes: 22.40 mm22.60 mm22.80 mm23.00 mm
RX608B
Reflex Racing Speed Dish Side Wall Plate Set (22.4 - 23.0) - Grey
10,00 CHF*
****This new plate set is slightly oversized from the nominal numbers. Expect them to be about 0.1mm larger than the nominal molded number. This makes this a larger plate set for those that don't want to true their tires at all. Just start with LP Mounted tires and the largest plate and adjust from there!**** Designed to make your life easier. These plates lock into your favorite Reflex Racing Speed Dish wheels for an increased wheel lip diameter. Having a larger diameter lip on the wheel leads to a smaller side wall aspect ratio on your tire, which very effectively reduces traction roll and steering response on your car. These plates are optimized to be used with "Low Profile" style front tires, which when mounted measure around 23.2mm on our wheels. The plate set comes with 4 different sizes: 22.40 mm22.60 mm22.80 mm23.00 mm
RX608G
Reflex Racing Speed Dish Side Wall Plate Set (22.4 - 23.0) - White
10,00 CHF*
****This new plate set is slightly oversized from the nominal numbers. Expect them to be about 0.1mm larger than the nominal molded number. This makes this a larger plate set for those that don't want to true their tires at all. Just start with LP Mounted tires and the largest plate and adjust from there!**** Designed to make your life easier. These plates lock into your favorite Reflex Racing Speed Dish wheels for an increased wheel lip diameter. Having a larger diameter lip on the wheel leads to a smaller side wall aspect ratio on your tire, which very effectively reduces traction roll and steering response on your car. These plates are optimized to be used with "Low Profile" style front tires, which when mounted measure around 23.2mm on our wheels. The plate set comes with 4 different sizes: 22.40 mm22.60 mm22.80 mm23.00 mm
RX608W
Reflex Racing Speed Dish Side Wall Plate Set (22.4 - 23.0) - Yellow
10,00 CHF*
****This new plate set is slightly oversized from the nominal numbers. Expect them to be about 0.1mm larger than the nominal molded number. This makes this a larger plate set for those that don't want to true their tires at all. Just start with LP Mounted tires and the largest plate and adjust from there!**** Designed to make your life easier. These plates lock into your favorite Reflex Racing Speed Dish wheels for an increased wheel lip diameter. Having a larger diameter lip on the wheel leads to a smaller side wall aspect ratio on your tire, which very effectively reduces traction roll and steering response on your car. These plates are optimized to be used with "Low Profile" style front tires, which when mounted measure around 23.2mm on our wheels. The plate set comes with 4 different sizes: 22.40 mm22.60 mm22.80 mm23.00 mm
RX608Y
Reflex Racing Titanium Reverse Thread Adjustable Front Axles
19,00 CHF*
Die Version 2 der beliebten Front Achsen mit Innengewinde. Jetzt aus Titanium für mehr Haltbarkeit. Die V2 Achsen ermöglichen es, den vorderen Offset um 1mm Spurweite in Schritten von 0,5 mm durch die mitgelieferten M3x0,5 mm Axle Shims anzupassen. Die Achsen mit umgekehrtem Gewinde sind kompatibel mit dem Reflex Racing RX28 und auch GL Racing oder RTRC Fahrzeugen. Durch die Umkehrung des Gewindes und die Verwendung einer Schraube anstelle einer Mutter, ist es weniger wahrscheinlich, dass sich die Frontpartie Ihres Fahrzeugs in den RCP-Schienen verfängt, wenn Sie Räder mit geringerem Offset fahren. Das Kit wird mit 2 Achsen, 4 Stück M3x0,5 Kupferscheiben und 2 Stück M2x4mm Kopfschrauben geliefert. Tipp! Abhängig vom verwendeten Radtyp kann es vorkommen, dass die Achsen ein wenig axiales Spiel haben (minimal). Sie können dies durch leichtes Abschleifen der äußeren Achse beheben, um sie etwas schmaler zu machen. *****************************This is the V2 of our reverse axles. Now made from Titamium for more durability. The V2 axles allow you to adjust your front offset 1mm of trackwidth in increments of 0.5mm though the included M3x0.5mm Axle Shims. Reverse thread axles compatible with your Reflex Racing RX28 and GL/Atomic cars. By reversing the thread and using a screw instead of a nut, the front end of your car is less likely to snag into the RCP rails when running lower offset wheels. The kit comes with 2 Axles, 4pcs of M3x0.5 Copper Shims and 2pcs of M2x4mm button head screws. Tip: Depending on the type of wheel you use, sometimes, the axles can have a little bit of axial side to side play (minimal). You can tighten this up by lightly sanding the outer axle to make is slightly narrower.
RX516V2
REFLEX RACING Speed Dish Wheel REAR- 14mm (White)
5,50 CHF*
All new from Reflex Racing is the Speed Dish Line of wheels. Designed with performance and durability in mind, these molded wheels have a 0.5mm outer ridge that matches the inner flange height of most 1/28 scale wheels. The result from this is a tire that is easier to glue (which we recommend) and also more stability to the tire in the case you prefer to use tape. Made from durable and tough glass reinforced nylon, these wheels are acetone safe so they can be re-used.The Taller aspect of the wheel makes the sidewall effectively smaller in order to also aid in the increase of corner speed.
RX600R14W
REFLEX RACING Speed Dish Wheel REAR- 14mm (Yellow)
5,50 CHF*
All new from Reflex Racing is the Speed Dish Line of wheels. Designed with performance and durability in mind, these molded wheels have a 0.5mm outer ridge that matches the inner flange height of most 1/28 scale wheels. The result from this is a tire that is easier to glue (which we recommend) and also more stability to the tire in the case you prefer to use tape. Made from durable and tough glass reinforced nylon, these wheels are acetone safe so they can be re-used.The Taller aspect of the wheel makes the sidewall effectively smaller in order to also aid in the increase of corner speed.
RX600R14Y