Wichtig: Der Swave W2 ESC wurde für die Verwendung von Ensotech™-zertifizierten Motoren und der jeweils neuesten Firmware optimiert. Die ESC wurden für den optimalen Einsatz und Schutz mit diesen zertifizierten Motoren entwickelt, die Leistungstests und Qualitätssicherung bestanden haben und die Qualifikationskriterien erfüllen. Diese Technologie hat sich bei vielen Rennfahrern und Podiumsplatzierungen bewährt, wenn sie den Ensotech™ Swave ESC und konforme Sensormotoren verwenden. Um vom Ensotec Kundenservice zu profitieren, empfehlen wir die Verwendung der unten aufgeführten Ensotech™ zertifizierten Sensormotoren: Marke Modell Stator RC-AURORA ARR BRUSHLESS 5500kv SLOTLESS RC-AURORA ARR BRUSHLESS 6200kv SLOTLESS RC-AURORA ARR BRUSHLESS 7000kv SLOTLESS LD POWER 1528 BRUSHLESS 5300KV SLOTLESS ENSOTECH Swave-ZM V3 3500KV + 4500KV SLOTLESS ENSOTECH Swave-ZM V3 5500KV SLOTLESS ENSOTECH Swave-ZM V3 6500KV  SLOTLESS RACE UNLIMITED XMM002-3500SE SLOTLESS RACE UNLIMITED XMM002-5500SE SLOTLESS ENSOTECH SWAVE-ZM V2 3500KV SLOTLESS ENSOTECH SWAVE-ZM V2 5500KV SLOTLESS ENSOTECH SWAVE-ZM V2 6500KV SLOTLESS ENSOTECH SWAVE-ZM V2 7500KV SLOTLESS   Bitte beachten Sie, dass die Verwendung von nicht-Ensotech™-zertifizierten Sensormotoren mit dem elektronischen Drehzahlregler (ESC) von Swave zum sofortigen Erlöschen der Ensotech™-Garantie führt (gilt nicht für sensorlose Motoren).  Beachten Sie bitte auch den Hinweis zum Löten der Anschlusskabel!      Swave-W2 Sensored Electronic Speed Controller makes technology essential to your modern mini R/C car. The principle of W2 to enhance heating dissipation. Used high watts thermal PAD, more copper inside PCB for current flow optimization, and the length of PCB increased 1mm compared to W.Besides, the schematic has also been re-engineered to improved control of Bluetooth power..... ready for future gadget tech. Ideally to use on microscale 1:28 RWD and shaft drive AWD touring car who needs liner and responsiveness on drifting and touring race. Enjoy the best value versus performance ratio, size, weight, technology as well as other advantages. Features "Blinky-mode" provides a fair racing environment between racers.  (Shows that all timing advance switched to zero)  Stunning size and weight Easy-to-use programming Firmware update available A professional set of customized parameters for the difficult race track Automatic recognition of Hall sensor’s position Settings configurations export and import. (You can save and load configuration or share out) Aluminum body   Firmware update and change setting  via Android version swave appsOptional UARTLINK-II programming cable Optional wireless EnsoBlueth Bluetooth adaptor Specification: * Dimensions (mm): 26.00(L)*13.20(W)*7.86(H) * Weight: 4.5g * Supply Voltage:  2s LiPo / 2s LiOn  * Const./Brust Current (A):  20/30A (under 90 degree Celsius) * Sensor input:  1 (5 pins) * Programming input:  1 * Receive input: 1 * Support motor type (Sensored): Slotless 15mm Brushless DC up to 7500kv * Support motor type (Sensorless): Slotless 15mm Brushless DC * BEC Output: 5V / 1.5A   PROPER GEARING ------------- >>> HERE Package Included:1* Swave-W2 ESC1* Receiver Cable (JST)1* Receiver Cable (JR)1* Motor Sensor Cable (product code: CABLE06)     Hinweise zum Löten der Anschlusskabel: Die Anschlusskabel (Motor und Lipo) müssen selber am ESC angelötet werden. Beachten Sie dabei, dass Sie das ESC nicht überhitzen, die Elektronik könnte dabei Schaden nehmen. Defekte ESC aufgrund von Überhitzung beim Löten sind von der Garantie ausgenommen. Wir empfehlen Ihnen beim Löten der Anschlusskabel ein Flussmittel zu verwenden, und den Lötvorgang möglichst kurz zu halten. Lassen Sie das ESC beim Löten der einzelnen Kabel zwischendurch immer wieder abkühlen. 

This newest high-speed UARTLINK-III programming cable to connect Swave-E2 & Swave-W & W2 to Android devices (not IOS) has higher download and upload speeds that your setting change process and the firmware update is a breeze.  Swave's ESC requires OTG (On The Go) protocol to communicate with Android devices.  Most latest Android devices have OTG.  If you are not sure there are some free of charge apps available in Google Play™ use to check your device. UARTLINK-III provides with OTG Micro-USB connector on the phone end, for Type-C USB Android device require to use "USB Type-C Adaptor", available HEREIf you have your own Type-C adaptor make sure the adaptor support OTG, some adaptor came with the phone doesn't support OTG communication protocol, it's only for charging purpose. ** This cable not for Swave-E "Swave ESC" programming app available to download from Google Play™ either download the apk file from HERE to install manually The firmware update process needs to run without interruption otherwise that can render the device unusable.  Processing time depends on the specific hardware configuration of the Android device and the quality of the internet data speed.   If you want to modify UARTLINK to UARTLINK-II,  please leave your request in your order, we will provide a 3 pin connector in the shipment.  You will need to remove the pin from the 2pin connector and insert to the 3pin connector.   

ENSO BLUETH-2 designed or IOS user, easily and remotely access your ESC to change the parameter and firmware update wirelessly, also telemetry monitors the battery voltage / ESC temperature/throttle and motor rpm, without leaving the driver to stand. An advantage of the unbelievable micro size you can place it anywhere inside the car. Each Bluetooth adaptor has its unique ID and password, prevent to mess up with other drivers' phones.  * Micro Size* Low energy Bluetooth* Wireless setting* Wireless firmware update* Telemetry monitor the battery voltage / ESC temperature / throttle / rpm Support ESC: Swave-E2 / Swave-W / Swave-W2 (doesn't support Swave-E)System Support: iPhone 7 or later / IPAD Pro or laterPCB Size: 1cm*1cm (exclude cables) Different to use Android version "ENSO BLUETH" and IOS version ENSO BLUETH-2 on IOS device;IOS has its own password protocol then the Android, if use Android version "ENSO BLUETH" on IOS device although there is no problem if you are the first time to establish the connection, if trying to reconnect again it’s prohibited by IOS system, you have to remove the "ENSO BLUETH" from the phone system then go back to Swave apps to search your "ENSO BLUETH" and input password again like you are the first time to establish the connection.    To use ENSO BLUETH-2 is no longer repeating the process. ENSO BLUETH-2 may communicate with some Android devices but Ensotech cannot guarantee and we cannot make its work on all kinds of Androids. If you are using Android device please purchase the Android version - ENSO BLUETH   IOS Swave apps available on App Store and its call "Swave Dev" 

Swave W / W2 and Swave E2 can now use a wireless connection via ENSO BLUETH.  You can easily and remotely access your ESC to change the parameter and firmware update, also telemetry monitors the battery voltage / ESC temperature/throttle and motor rpm, without leaving the driver stand. With the technology of the ultra-low-power module, you can leave it with the ESC all the time. An advantage of the unbelievable micro size you can place it anywhere inside the car.Each ENSO BLUETH has its own unique device name and password, prevent to mess up with other drivers' phones.  * Micro Size* Low energy* Wireless setting* Wireless firmware update* Telemetry monitor the battery voltage / ESC temperature / throttle / rpm Support ESC:  Swave-E2 / Swave-W / W2 (doesn't support Swave-E)System Support: Android version 5.0 (Lollipop) or laterSize: 1cm*1cm (exclude cables) Video Link (Wireless and How to make the connection)https://youtu.be/7K48fuiJrEUhttps://youtu.be/Dv94GTC7uBc Different between to use Android version "ENSO BLUETH" and IOS version ENSO BLUETH-2;IOS has its own password protocol then the Android, if use Android version "ENSO BLUETH" on IOS device although there is no problem if you are the first time to establish the connection, if you want to reconnect again it’s prohibited by IOS system, you have to remove the "ENSO BLUETH" from the phone system then go back to swave apps to search your "ENSO BLUETH", input password again like you are the first time to establish the connection.  If you are using IOS device please purchase the IOS version - ENSO BLUETH-2 "ENSO BLUETH" able to communicate with most popular Android devices available on the market but Ensotech cannot guarantee it works on all kinds of Android devices.** TO GET THE BEST CONNECTION RESULT, PLEASE CLEAR THE PHONE CACHE MEMORY AND UNNECESSARY BACKGROUND APPS BEFORE USE OR SIMPLY RESTART THE PHONE **

A pack of 2 pcs replacement on/off switch button for Swave-E2 / W / W2 Color: Blue Material: Silicone