The new ride height gauge makes it easier to read Ride Height Readings on chassis and motor mounts particularly when they are chamfered like on the RX28.
Option Steel Lower Pod Plate adds approximately 2.7g of weight to the rear pod of your car. The effect is a little more stability on power. Great for lower bite and faster classes.
This titanium shaft is far tougher than the stock aluminum diff all while maintaining light weight. As a plus all our new shaft designs allow for the use of a thrust bearing on the outside of the diff instead of a normal bearing to handle side load much better. This leads to a smoother, longer lasting diff.
The Reflex Racing Mass Damper Set is designed to smooth out your 1/28 scale car by reducing the amplitude of vibration on the front end caused by the uneven nature of RCP Tracks. The mass damper is mounted on the ballast weight hole on any Reflex Racing Carbon Bumper or on the body clip posts of your RX512 Jomurema bumper. The result is a car that is smoother to drive and more controllable at high speed and through bumpy sections. Adjust the Damper by using a different combination of weights.
The set includes:
3x 0.9g Tungsten Weights1x 4mm aluminum post2x M2x3 CS Screws.
These sleek-looking steel bumper weight set allow you to fine tune your weight bias on your Mini-Z when used in combination with any of our Carbon Fiber Bumpers. When running on bumpy or high grip environments, playing around with a little bit of nose weight can impact tremendously the behavior of your car. This weight set allows you to fine tune your nose weight in 1g increments. This is easily achieved by stacking the thru-hole weights and then clamping them down on the bumper with the threaded weight on top.
Included in the set is:
2x 1g thru weights
1x 1g threaded weight
1x M2x4CS Screw
1x M2x6CS Screw
All New from Reflex Racing is an Industry first Hard Case Lipo!!! This battery is designed to fit into most modern 1/28 scale chassis.
Why hardcase? Well, hardcase batteries have numerous benefits. Due to its design, a hardcase cuts down on connection points, uses more efficient plugs and thicker wire. These 3 elements drop the internal resistance of the entire circuit leading to better overall current flow, less heat loss and more performance. Couple that with the additional voltage capacity (these are safe to charge to 8.6v!) and the result is a sure fire winner.
Additionally, hard case batteries simply wire better. In categories like Pan Car, where wiring is a bit tricky to fit under the low slung bodies, the hardcase bullet to battery system opens up a tremendous amount of space under the body.
Lastly, hard case batteries are also safer and tougher. Wires don't break at the exit of the shrink, so shorts are minimized and, the hard case also protects the cells from damage better, as well as isolates them from possible punctures or shorts caused by the chassis or impacts.
We recommend to charge the batteries at 1.0A
Dimensions:
44.5x19.7x13mm
Weight:
17g
Includes:
1 battery pack
2 gold bullet plugs
The Reflex Racing Mass Damper Set is designed to smooth out your 1/28 scale car by reducing the amplitude of vibration on the front end caused by the uneven nature of RCP Tracks. The mass damper is mounted on the ballast weight hole on any Reflex Racing Carbon Bumper or on the body clip posts of your RX512 Jomurema bumper. The result is a car that is smoother to drive and more controllable at high speed and through bumpy sections. Adjust the Damper by using a different combination of weights and springs.
The set includes:
2x 0.9g Tungsten Weights1x 8mm aluminum post-2x M2x3 CS Screws. (use M2x3 CS Screw on top of the mass damper top spring when installing 1 weight).1x M2x6 BH Screw (use M2x6 BH Screw plus M2 gold washer on top of top spring when installing 2 weights).1x M2 Gold Washer2x Black MD Spring (Soft)-2x Silver MD Spring (Medium)
Made with flexible Silicone Sheathing, this ESC to receive link wire is more easily coiled, routed and shorter than std wires usually supplied with electronics. Up your wiring game and use this all black wire for the stealth look! This set comes with 1 wire. ESC Side plug is not installed. You must match the wire order to the oem wire supplied with your electronics.
Made with flexible Silicone Sheathing, this ESC to receive link wire is more easily coiled, routed and shorter than std wires usually supplied with electronics. Up your wiring game and use this all black wire for the stealth look! This set comes with 5 wires. ESC Side plug is not installed. You must match the wire order to the oem wire supplied with your electronics.
2x Kugellager für das Hauptzahnrad.Passend für Reflex Racing, PN Racing, Nexx Racing Hauptzahnräder.Dimensionen: Innendruchmesser 4mmAussendurchmesser 7mmBreite 2mm
What makes the Reflex Ball Diff Special? Attention to details. We worked on sourcing the highest quality materials and ended up with a light weight ball diff that has better engagement and acceleration.
The ball diff comes standard with super hard steel diff rings, 7075 T6 aluminum diff shaft, carbide diff balls, hard o-ring for tighter adjustment, our specially designed 10 ball spur gear and lightweight 7075 aluminum shaft and diff parts. The V4 diff now also comes with a molded spur and spur gear covers. The spur gear is super durable, quieter and much longer lasting. The covers are now about 50% lighter than the aluminum variants, which gets the weight down to a scant 6.6g with covers and 5.8g without (including the left hub).
Montage Anleitung V2/V3/V4 Diff.
Das Reflex V3 Werkzeugset - jetzt mit einem neuen Griff Design und zusätzlich mit einem Philips 00 Kreuzschraubenzieher, welcher sich bestens für die kleinen Pivot Schrauben des RX28 eignet. Das V3 Werkzeugset kommt wieder in einem praktischen Etui, welches die Werkzeuge schützt und Ordnung hält. Es beinhaltet alle notwendigen Werkzeugschlüssel, um deinen RX28, GL Racing, RTA oder MWX zu montieren. Das Werkzeugset enthält: Inbus-Schrauber:0,9mm1,3mm1,5 mmBox-Schlüssel:4.0mm4,5 mm Phillips-Schrauberzieher:#0#00
It's finally here! Our all new Gear differential was designed to be a high quality and high performance addition to your 1/28 scale car. More rotation and harder acceleration than the ball differential yields a car that is often about a tenth faster to drive in high traction surfaces. The feel of this gear diff is very balanced and this makes the acceleration super smooth and strong. At only about 4.7g, it is also super light for less rotational mass.
The gear diff is sealed from the elements as the gears are inside a machined aluminum case in which you can larger amounts of grease to change the behavior of the differential action. The ticker the grease, the lower response into the corner, but this could be at the expense of a little bit of exit traction. We don't recommend going too heavy on the oil (maybe use no more than 1 or 2k CST oil), but you can use oil with no leakage at the spur and only slight leaking at the outputs.
MANUAL
**Please not the diff is not sealed at the bearings, so it is not designed to be "filled" with oil , but a healthy amount can be used when building. Left hub is not included.
This charging cable was designed to be used with XT60 output chargers to be used with our hard case battery packs. Durable, stylish and perfect length cables to help you tidy up your pit space!
This charging cable was designed to be used with XT60 output chargers to be used with our hard case battery packs. Durable, stylish and perfect length cables to help you tidy up your pit space!
This is a set of Full Ceramic Bearings for you 1/28 scale Pan Car. Full Ceramic Bearings offer many benefits as outlined below:
Reduced Friction: They provide lower rolling resistance, which can improve the car's speed and overall efficiency.
Enhanced Durability: The wear-resistant nature of ceramic bearings means they can last longer under the high stress.
Lightweight: While not a lot, a full set of ceramics drops about 0.5g off your car.
Reduced Maintenance (somewhat): The low friction and wear properties eliminate the need for oil or grease. However, as our bearings have no races, they can allow more debris and tire dust to enter the bearings.
Corrosion Resistance:As they are not metallic, your bearings can be washed with something like dish soap and water.
https://www.youtube.com/watch?v=7tmryrOY6PA
Replacement front end for your RX28 or RX28K Upgrade
It includes:
BulkheadUpper and Lower Hinge PinsGray (Hard Arms)RX28 Shock Set with Green Front SpringsFront Shock TowerNecessary Hardware For Installation of all parts on the front end.
Required:
KnucklesFront Axles
All New RX28 Steel Chassis for your RX28G2 Plate Cars. This new chassis allow for fore and aft movement of 20mm wide batteries as well as making it compatible with our new 400mah batteries that are 24mm wide. This new chassis kit comes with lateral CF braces to locate the battery side to side, but also to stiffen the front to back structure of the car for more precise handling and higher corner speeds. The kit is finished off with a new forward center shock mount that incorporates a band-less battery hold down that is more reliable and easier to use.
All New from Reflex Racing is our 400mah LiHv battery. This battery offers longer runtime, lower IR and overall better performance for longer races vs the 340mah pack all while only weighing an extra 2g. This battery is slightly bigger so, it will only fit your RX28 when using the 24mm battery conversion kits or the 102mm WB Chassis. This battery will fit most AWDs car in the market as well as other cars that are capable of fitting a 24mm wide battery.
Why hardcase? Well, hardcase batteries have numerous benefits. Due to its design, a hardcase cuts down on connection points, uses more efficient plugs and thicker wire. These 3 elements drop the internal resistance of the entire circuit leading to better overall current flow, less heat loss and more performance. Couple that with the additional voltage capacity (these are safe to charge to 8.6v!) and the result is a sure fire winner.
The Benefit of having a battery that sits solidly in place on the chassis offers a handling advantage as there are no plugs and wires dangling inside the car. (Just think, we use 0.9g mass damper weights to stability our cars. Plugs and wires often represent more than this weight and they are jumping up and down inside the body of the car when using a soft case pack. ). The result is a car that behaves more smoothly. Additionally, hard case batteries simply wire better. In categories like Pan Car, where wiring is a bit tricky to fit under the low slung bodies, the hard case bullet to battery system opens up a tremendous amount of space under the body.
Lastly, hard case batteries are also safer and tougher. Wires don't break at the exit of the shrink, so shorts are minimized and, the hard case also protects the cells from damage better, as well as isolates them from possible punctures or shorts caused by the chassis or impacts.
We recommend to charge the batteries at 1.0A
Dimensions: 44.5x24x12.5mm
Weight: 19g
Includes:
1 battery pack2 gold bullet plugs
You Can use Cable no: RRE013 to charge.
Dieses kurze Lenkhorn wurde für Anwendungen mit hoher Traktion entwickelt, bei denen Dein Auto zu kantig ist und Du ein langsameres Lenkgefühl wünschst. Es ist ideal für Pan Car und grössere fliessende Rennstrecken, wo Du nicht so viel Lenkung benötigst und wo du normalerweise weniger als 85% Dual Rate fährst.
Dieses Servo Horn bietet eine linearere Lenkgeometrie für Deinen RX28. Durch die Verschiebung der Drehpunkte des Servohorns nach vorne, erreichen wir einen höheren Winkel auf die Links, die weniger Ackerman-Effekt auf Ihre Vorderreifen erstellt. Das Ergebnis ist ein Lenkgefühl, das weniger exponentiell ist, wenn die Dual Rate erhöht wird. So kannst Du bei hoher Traktion weniger Lenkeinschlag haben oder bei engen Strecken mit 180ern, wo mehr Lenkeinschlag erforderlich ist, aggressiver fahren.
Shed some weight from up top for an even lighter CG. This shaft sheds 0.3g from your top shock, leaving behind a 1.41g top shock. When combined with the new aluminum turnbuckles, part no: RX28A-44, it will shed 0.85g up top.
Shed some weight from up top and look good while doing it with these. Both Turnbuckles together save approximately 0.5g from one of the highest points of the car. When combined with the New Aluminum Top Shock Shock Shaft it sheds about 0.85g.
The V2 have a new hard-coating for longer lasting wear characteristics. High quality 64 Pitch 7075 T6 Aluminum pinion gears for your 1/28 scale car. Each gear set comes with: 1 x 10T pinion
1 x 11T pinion
1 x 12T pinion
1 x 13T pinion
1 x 14T pinion
1 x 15T pinion
All new from Reflex Racing is our Aluminum Tweak Station. Precision machined from 7075 aluminum and high grade stainless steel, this tweak station is precise, light weight and easy to use.
The tweak station features 3 adjustable feet as well as a bubble level to set the station level in North-South and East-West. The Station pivoting bar is also ball raced for minimum friction and maximum precision.
This station is compatible with any wheelbase from 98mm all the way to 116mm so most of you 1/28 scale cars should be able to be adjusted with this awesome tool
Set of 3 tire gauges to make your tire measuring experience much easier.
To Use:
Select the appropriate gauge by measuring against the tire.Once selected, push the open side of the gauge onto the tire. Once you feel slight resistance and the center of the wheel is aligned with the resistance point, this is the measurement for your tire diameter.
All new from Reflex Racing is the MC1 30A ESC. This ESC is not just a re-labeled unit, but rather a proprietary ESC and Software designed from the ground up specifically for 1/28 scale (and other Micro scales) for racing. Curated to use the highest quality components and craftsmanship, the result is an Ultra-High Performance, super adjustable and durable ESC. The ESC is adjustable via the RRE024 MC1 Programming Box and has been designed to be used with a soon to be released bluetooth dongle and App. *All ESCs come with a 90 day limited warranty which covers manufacturing defects or DOA units. Reverse polarity connection is not covered under warranty.**Please note that the price reflects the current additional tariff rate.
Anleitung:
MC1 Manual
