Inspired by 1/8 design and revised to make it match the needs of 1/28 scale cars. The Ocho is perhaps the highest downforce, most balanced handling, "Wedge" type body ever developed for 1/28 scale cars.Developed and tested by the best of the best all across the country this body simply works. When running in an "Open/Pan Car" class, if you are not running one of these, you basically will be at a disadvantage, we can guarantee that. Due to the design, the Ocho allows you to hold more throttle, for longer in sweeping corners. The super balanced handling allow you to drive aggressively and with it's smooth-design front end, when combined with a Reflex RX519 or upcoming RX533 Bumper, it slides off the RCP Rails much better than other "wedge" Stye bodies.
This bodyIS NOT LEGAL FOR PNWC COMPETITION. (It's just too good)
This is Rad Body's response for PNWC Pan Car Competition. Fully legal and ready to race, the Skillet is Low CG and Perfectly balanced for Rubber Tire 1/28 scale racing. Please note that due to the extremely low CG Design, the Skillet may not fit some cars with Higher CG Rear suspension set ups.
The Wing Things are designed to make mounting your wing much easier. Install the screw from the bottom of the body and thread them into the wing thing threads. You can hold the wing thing with a 4.5mm hex wrench to fully tighten.
The total weight of the 2 wing things and 2 M2x4 is roughly 0.5g; about the same weight as using a couple of steel hex nuts and 6mm steel screws that are typically included in body sets.
The Wing Things are designed to make mounting your wing much easier. Install the screw from the bottom of the body and thread them into the wing thing threads. You can hold the wing thing with a 4.5mm hex wrench to fully tighten.
The total weight of the 2 wing things and 2 M2x4 is roughly 0.5g; about the same weight as using a couple of steel hex nuts and 6mm steel screws that are typically included in body sets.
The Wing Things are designed to make mounting your wing much easier. Install the screw from the bottom of the body and thread them into the wing thing threads. You can hold the wing thing with a 4.5mm hex wrench to fully tighten.
The total weight of the 2 wing things and 2 M2x4 is roughly 0.5g; about the same weight as using a couple of steel hex nuts and 6mm steel screws that are typically included in body sets.
These sleek-looking steel bumper weight set allow you to fine tune your weight bias on your Mini-Z when used in combination with any of our Carbon Fiber Bumpers. When running on bumpy or high grip environments, playing around with a little bit of nose weight can impact tremendously the behavior of your car. This weight set allows you to fine tune your nose weight in 1g increments. This is easily achieved by stacking the thru-hole weights and then clamping them down on the bumper with the threaded weight on top.
Included in the set is:
2x 1g thru weights
1x 1g threaded weight
1x M2x4CS Screw
1x M2x6CS Screw
All New Mako X gives our most successful GT Body some revisions to make your 1/28 car a little more stable and precise in high traction conditions. The Revisions include some ridges above the front wheel well and a lower rear window and wing. The front end changes make the steering inputs more crisp without making it nervous, while the lower rear window generates more downforce. This allowed us to lower the rear wing substantially, and when combined with the lower window the result is a car that stays more flatter for more high speed stability and better control in high traction conditions.
Inspired by the current fastest production hyper car at the Nurburgring, the Catfish is Rad Body's Second Foray into GT Bodies.Having mellower initial steering but higher corner speed than the Mako and Mako X, the Catfish has a very neutral and easy to drive feel.While perhaps not as quick around tighter corners, the increased stability and higher corner speed makes this body shine in higher bite and higher speed corners.
Perfekter Spoiler für den Jomurema GT01 Body.Um den Spoiler am Body zu befestigen, werden keine Schrauben benötigt.Der Spoiler ist 3D gedruckt mit PA 12 Material. Gewicht: 3gFarbe: schwarz (Material kann bemalt werden)Entgrate die Teile bei Bedarf mit einem Cutter-Messer. Drücke den Spoiler mit einem flachen Schraubendreher vorsichtig auf den Body. Nutze den Raum zwischen der oberen Tragfläche und dem Flügelsockel, direkt über den Stiften, wie auf Bild 1 (in der Anleitung) gezeigt.
Du kannst die Stifte und die äußeren Seitenplatten mit Sekundenkleber am Body befestigen! (mehr Stabilität)
Perfekter Spoiler für den Jomurema GT01 Body mit verstellbarem Flügel!Um den Spoiler am Body zu befestigen, werden keine Schrauben benötigt.Der Spoiler ist 3D gedruckt mit PA 12 Material. Gewicht: 3gFarbe: schwarz (Material kann bemalt werden)Entgrate die Teile bei Bedarf mit einem Cutter-Messer. Drücke den Spoiler mit einem flachen Schraubendreher vorsichtig auf den Body. Nutze den Raum zwischen der oberen Tragfläche und dem Flügelsockel, direkt über den Stiften, wie auf Bild 1 (in der Anleitung) gezeigt.
Du kannst die Stifte und die äußeren Seitenplatten mit Sekundenkleber am Body befestigen! (mehr Stabilität)
Body Clips - farbig10 Stück Gold10 Stück Schwarz10 Stück SilberThe most frequently lost item in mini RC has been addressed with our redesigned body clip. It now features an enhanced hook, making it simpler to attach to the body post.
Front Bumper für Lexan Karosserien1.5mm CFK, MattVerschiedene Montagelöcher für Body Posts für eine optimale Positionierung, je nach KarosserieKompatibel mit GLR, GL-GT, GTR, RX28, MWX R.1, Nexx Specter, Atomic, MR03, MR04 uvm.Grösse: 78.5 x 35mmGewicht: 3.1g
Front Bumper für Lexan Karosserien1.5mm CFK, MattVerschiedene Montagelöcher für Body Posts für eine optimale Positionierung, je nach KarosserieKompatibel mit GLR, GL-GT, GTR, RX28, MWX R.1, Nexx Specter, Atomic, MR03, MR04 uvm.Grösse: 78.5 x 35mmGewicht: 2.6g
Front Bumper für Lexan Karosserien1.5mm CFK, MattVerschiedene Montagelöcher für Body Posts für eine optimale Positionierung, je nach KarosserieKompatibel mit GLR, GL-GT, GTR, RX28, MWX R.1, Nexx Specter, Atomic, MR03, MR04 uvm.Grösse: 78.5 x 30mmGewicht: 2.9g
Front Bumper für Lexan Karosserien1.5mm CFK, MattVerschiedene Montagelöcher für Body Posts für eine optimale Positionierung, je nach KarosserieKompatibel mit GLR, GL-GT, GTR, RX28, MWX R.1, Nexx Specter, Atomic, MR03, MR04 uvm.Grösse: 78.5 x 30mmGewicht: 2.3g
Front Bumper für Lexan Karosserien1.5mm CFK, MattVerschiedene Montagelöcher für Body Posts für eine optimale Positionierung, je nach KarosserieKompatibel mit GLR, GL-GT, GTR, RX28, MWX R.1, Nexx Specter, Atomic, MR03, MR04 uvm.Grösse: 78.5 x 25mmGewicht: 1.9g
Front Bumper für Lexan Karosserien1.5mm CFK, MattVerschiedene Montagelöcher für Body Posts für eine optimale Positionierung, je nach KarosserieKompatibel mit GLR, GL-GT, GTR, RX28, MWX R.1, Nexx Specter, Atomic, MR03, MR04 uvm.Grösse: 74 x 25mmGewicht: 1.8g
Front Bumper für Lexan Karosserien1.5mm CFK, MattVerschiedene Montagelöcher für Body Posts für eine optimale Positionierung, je nach KarosserieKompatibel mit GLR, GL-GT, GTR, RX28, MWX R.1, Nexx Specter, Atomic, MR03, MR04 uvm.Grösse: 74 x 25mmGewicht: 1.8g
Front Bumper für Lexan Karosserien1.5mm CFK, MattVerschiedene Montagelöcher für Body Posts für eine optimale Positionierung, je nach KarosserieKompatibel mit GLR, GL-GT, GTR, RX28, MWX R.1, Nexx Specter, Atomic, MR03, MR04 uvm.Grösse: 74 x 20mmGewicht: 1.9g
When you think innovation, you don't often think body posts, however these are one of the favorite products we have released. Our all new body post system is full of little details that will make your car look cleaner, make it more durable and also allow you to adjust you body height easier and more precisely than before.
PNWC 2024 Paris allowed body for 2WD Stock and GTLM Super Stock class
Description
Configurable for 98mm wheelbase.
The body comes unpainted. painting is not necessary as it was made of white color material with a glossy finish
Features Reversible Side Body Clip which allows lowering body height by 1mm when installed in the reversed order.
Includes
Lexan Roof
Lexan Spoiler
Front & Side Body Clips
Headlight Taillight Lens in Clear
Headlight Taillight Lens in Red
Screws
Requirement
Kyosho Mini-Z MR-02, MR-03, PN 2.5W
GL Racing GLA, GLR, GT, GTRImportant:
For use with a Reflex RX28 or MWX R1 chassis, the body clip PN-600524RX is required (2mm offset)
Manual Download
PNWC 2024 Paris allowed body for 2WD Stock and GTLM Super Stock class
Description
Configurable for 98mm wheelbase.
The body comes unpainted. Painting is not necessary as it was made of orange color material with a glossy finish
Features Reversible Side Body Clip which allows lowering body height by 1mm when installed in the reversed order.
Includes
Lexan Roof
Lexan Spoiler
Front & Side Body Clips
Headlight Taillight Lens in Clear
Headlight Taillight Lens in Red
Screws
Requirement
Kyosho Mini-Z MR-02, MR-03, PN 2.5W
GL Racing GLA, GLR, GT, GTRImportant:
For use with a Reflex RX28 or MWX R1 chassis, the body clip PN-600524RX is required (2mm offset)
Manual Download
PNWC 2024 Paris allowed body for 2WD Stock and GTLM Super Stock class
Description
Configurable for 98mm wheelbase.
The body comes unpainted. Painting is not necessary as it was made of yellow color material with a glossy finish
Features Reversible Side Body Clip which allows lowering body height by 1mm when installed in the reversed order.
Includes
Lexan Roof
Lexan Spoiler
Front & Side Body Clips
Headlight Taillight Lens in Clear
Headlight Taillight Lens in Red
Screws
Requirement
Kyosho Mini-Z MR-02, MR-03, PN 2.5W
GL Racing GLA, GLR, GT, GTRImportant:
For use with a Reflex RX28 or MWX R1 chassis, the body clip PN-600524RX is required (2mm offset)
Manual Download
Body Side Clips for Reflex RX28 and MWC R1 Chassis for PN Racing C9 ABS / Plastic Body (Art. PN-600500)
High-quality material 3D Print2mm forward offset for Reflex RX28 and MWX R1 chassis
Carbon Fiber Adapter for PN Racing C9 ABS / Plastic Body (Art. PN-600500)
Made from high-strength carbon fiber to reduce weight and adds durability.The body height is adjustable using the shims provided in the kit.Additional shims can be used to increase body height.
Requirement:
PN Interchangeable body mount (BM001) or compatibel GT55
PNR C9 Body Set
Color:
Carbon fiber black.
Includes:
1 x carbon fiber body mount
2 x 0.5 mm Fiberglass spacer
1 x 1.0 mm Fiberglass spacer
1 x 2.0 mm Fiberglass spacer
This bumper was developed to be in compliance with the 2024 PNWC Bumper Rules. The new requires there to be a 2mm gap between bumper and body if the bumper is made out of CF. This bumper retains the same shape as the RX528 Mako Bumper, but also has a nested, front TPU liner which satisfies the rule as the leading edge is now made from flexible, rubber like material (albeit, still super rigid).
This bumper is slightly heavier, but not by much. We recommend using CA to attach the bumper more securely to the CF part.
Sturdy, good looking and lightweight, this bumper is perfect to mount "Pan Car" Type bodies on your 1/28th scale car. The design splits the front posts further apart than others in the market for better body support. This leads to better steering and longer lasting bodies.
LOWER PLATE ONLY FOR THE KYOSHO C8 CORVETTE BODY
THE PLATE ONLY FITS THE MWX JMA BUMPER KIT SO IN ORDER TO USE THIS PLATE YOU NEED TO PURCHASE A JM BUMPER KIT
JOMUREMA BUMPER KIT (MX-JMA-23) - MWX Performance
The bodies are made specifically for Silver Horse RC and they fit perfectly on Kyosho MR03, PN, Atomic, GL, and any other Mini-Z compatible chassis. The Sauber is a 102 mm body or as many call "LM." The paint is high gloss titanium silver and tested tough with months of racing and testing. The body weighs only 1.3 oz before the clips are installed. We do not mount the side clips so you can make height adjustments before you glue them into place.
The side clips can be placed in two positions, the standard height and lowered racing height, see the instruction video on our YouTube Channel for help!
Comes with two (2) side clips a nose mounting clip and the body.
The bodies are made specifically for Silver Horse RC and they fit perfectly on Kyosho MR03, PN, Atomic, GL, and any other Mini-Z compatible chassis. The Sauber is a 102 mm body or as many call "LM." The paint is high gloss titanium silver and tested tough with months of racing and testing. The body weighs only 1.3 oz before the clips are installed. We do not mount the side clips so you can make height adjustments before you glue them into place.
The side clips can be placed in two positions, the standard height and lowered racing height, see the instruction video on our YouTube Channel for help!
Comes with two (2) side clips a nose mounting clip and the body.
Front Bumper and Body Mount for PN C9 Body
Material: Black PETG
Requirement:
PNR C9 ABS Body Carbon Fiber Adapter (PN-CP650)
PNR C9 Plastic Body Set (PN-600500W, PN-600500Y, PN-600500O)
IncludesFront & Side Body Clips: Reversible Side Body Clip which allows lowering body height by 1mm when installed in the reversed order. Requirement
PNR Concept C9 Body #600500
Carbon-Frontstoßstange für den Mercedes AMG GT3 zur Verstärkung der Karosserie. Neue gleitende Karosseriepfosten-Befestigungssystem sorgen für eine perfekte Übereinstimmung mit der Karosserie Löcher. Die V2-Version enthält die Carbon-Bodyclip und die Carbon-Höhenausgleichsscheibe perfekt an die Karosserie angepasst.
Wird mit 4 Schrauben geliefert.
Für die Verwendung mit einem RTA oder MRZ Chassis wird die Body Mount Base RT074 benötigt.Für die Verwendung mit einem GL Racing (GLR, GLA, GLR-GT,..), Kyosho MR03, Nexx Racing (Bison, Skyline, Specter) oder PN Racing Chassis wird die Body Mount Base RT075 benötigt.
In der Zeit vom 12. - 22. April 2025 schalten wir einen Gang zurück und die Bearbeitungszeit von Bestellung verzögert sich etwas.
Wir wünschen euch frohe Ostern und viel Erfolg bei der Eiersuche.
