Weight for balance Brass
High Clamp Force T-Plate Mount
Machined threads allow for higher clamping force on T-Plate to prevent shifting during high g-force cornering. Application of high torque to stock self tapping screws to prevent shifting of T-Plate often lead to stripped screw holes.
Double length aluminum T-Plate Mount with 4 interlocking tabs to insure precise alignment with chassis. Alignment of T-Plate mount is achieved thru interlock of holder to chassis alignment tabs instead of self tapping screw torque.
Countersunk crews are inserted one adjustment position after of T-Plate screw hole. Therefore, chassis with stripped holes for T-Plate can be salvaged with this T-Plate Mount that use a different hole location
Installation Instructions
Note that since T-Plate Mount is double length, only the forward two T-Plate positions can be used on the chassis. (This is usually not an issue since the forward two position is enough to accommodate pretty much all bodies.)
Install the two countersunk screws to hold the T-Plate Mount onto the chassis. Do not over tight the self tapping screws, or the hole on the chassis may strip.
Fasten the T-Plate onto the holder with two machine screws. Be sure the machine screw threads protrude past the T-Plate Mount when the screws are seated. This will insure full thread engagement. Machine screws can then be torque tighter than the self tapping countersunk screws to securely fasten the T-Plate. Take care not to over torque machine screws.
It is advisable to test fit the T-Plate on the holder with the machine screws first to verify that that the machine screw threads protrudes past the holder. A minimum of 1 thread protrusion is recommended.
This is brand new develop Mini-Z tire call KS Compound, much more grip and long life.All new KS Compound tire with PNR and KS logo at the sidewall.All new KS Compound SeriesKS1030 Slick Front Tire SUPER SOFTKS1034 Slick Front Tire SOFTKS1038 Slick Front Tire MEDIUMKS1042 Slick Front Tire FIRMKS2020 Slick Rear Tire SUPER SOFTKS2024 Slick Rear Tire SOFTKS2028 Slick Rear Tire MEDIUMKS2820 Radial Rear Tire SUPER SOFTKS2824 Radial Rear Tire SOFTKS2828 Radial Rear Tire MEDIUM
This is brand new develop Mini-Z tire call KS Compound, much more grip and long life.All new KS Compound tire with PNR and KS logo at the sidewall.All new KS Compound SeriesKS1030 Slick Front Tire SUPER SOFTKS1034 Slick Front Tire SOFTKS1038 Slick Front Tire MEDIUMKS1042 Slick Front Tire FIRMKS2020 Slick Rear Tire SUPER SOFTKS2024 Slick Rear Tire SOFTKS2028 Slick Rear Tire MEDIUMKS2820 Radial Rear Tire SUPER SOFTKS2824 Radial Rear Tire SOFTKS2828 Radial Rear Tire MEDIUM
This is brand new develop Mini-Z tire call KS Compound, much more grip and long life.All new KS Compound tire with PNR and KS logo at the sidewall.All new KS Compound SeriesKS1030 Slick Front Tire SUPER SOFTKS1034 Slick Front Tire SOFTKS1038 Slick Front Tire MEDIUMKS1042 Slick Front Tire FIRMKS2020 Slick Rear Tire SUPER SOFTKS2024 Slick Rear Tire SOFTKS2028 Slick Rear Tire MEDIUMKS2820 Radial Rear Tire SUPER SOFTKS2824 Radial Rear Tire SOFTKS2828 Radial Rear Tire MEDIUM
This is brand new develop Mini-Z tire call KS Compound, much more grip and long life.All new KS Compound tire with PNR and KS logo at the sidewall.All new KS Compound SeriesKS1030 Slick Front Tire SUPER SOFTKS1034 Slick Front Tire SOFTKS1038 Slick Front Tire MEDIUMKS1042 Slick Front Tire FIRMKS2020 Slick Rear Tire SUPER SOFTKS2024 Slick Rear Tire SOFTKS2028 Slick Rear Tire MEDIUMKS2820 Radial Rear Tire SUPER SOFTKS2824 Radial Rear Tire SOFTKS2828 Radial Rear Tire MEDIUM
Der flexibelste Motorenhalter von PN Racing mit einstellbarem Radstand von 93 - 102 mm.Features:
Compatible with PNR2.5W, MR015, MR02 and MR03
Wheelbase adjustable from 93mm to 102mm in 1mm increment. Include both 93-102mm standard width and optional parts MR2395D 98-102mm LM width Differential Carrier.
Wheelbase adjusted with only 2 screws.
Wheelbase adjustment does not affect gear mesh or suspension set-up. Allows quick testing of different wheelbase at the track.
Motor drops down for adjustment without affecting suspension set-up especially on a tri-damper set-up.
Multiple motor height positions possible for all track surfaces.
Four ride height adjustments with 2 eccentric bearing holders.
The ultimate motor mount. Results of years of improvement to Mini-Z motor mount designs.
Attention:This motor mount only working with the motor with 2 screw holes, all Kyosho motor can't install to this motor mount
PN Lexan Body Kit 600800K for Mini-Z MR03 and PN 2.5 Chassis
Configurable for 98mm wheelbase.
The body comes unpainted.
0.7mm Version
Requirement:
Kyosho Mini-Z MR-02, MR-03 or PN 2.5W chassis
1/28 AWD Chassis e.g. GL, Atomic, RTA
This is brand new develop Mini-Z tire call KS Compound, much more grip and long life.All new KS Compound tire with PNR and KS logo at the sidewall.All new KS Compound SeriesKS1030 Slick Front Tire SUPER SOFTKS1034 Slick Front Tire SOFTKS1038 Slick Front Tire MEDIUMKS1042 Slick Front Tire FIRMKS2020 Slick Rear Tire SUPER SOFTKS2024 Slick Rear Tire SOFTKS2028 Slick Rear Tire MEDIUMKS2820 Radial Rear Tire SUPER SOFTKS2824 Radial Rear Tire SOFTKS2828 Radial Rear Tire MEDIUM
Der flexibelste Motorenhalter von PN Racing mit einstellbarem Radstand von 93 - 102 mm.Features:
Compatible with PNR2.5W, MR015, MR02 and MR03
Wheelbase adjustable from 93mm to 102mm in 1mm increment. Include both 93-102mm standard width and optional parts MR2395D 98-102mm LM width Differential Carrier.
Wheelbase adjusted with only 2 screws.
Wheelbase adjustment does not affect gear mesh or suspension set-up. Allows quick testing of different wheelbase at the track.
Motor drops down for adjustment without affecting suspension set-up especially on a tri-damper set-up.
Multiple motor height positions possible for all track surfaces.
Four ride height adjustments with 2 eccentric bearing holders.
The ultimate motor mount. Results of years of improvement to Mini-Z motor mount designs.
Attention:This motor mount only working with the motor with 2 screw holes, all Kyosho motor can't install to this motor mount
We are proud to introduce the all new PNR2.5W after close to 2 years of design and testing. PNR2.5W is the must have DIRECT replacement for all existing Mini-Z MR03 chassis.
Engineered and design ground up by World Champions, the chassis is made of Nylon with fiberglass and ABS material. PNR 2.5W has
- Lower Battery CG
- Hard Coating Battery Terminals
- Better heat dissipation for batteries and electronics
- Lighter and Wider chassis to provide superb stability
- Ample top deck space to allow 3rd party receivers
- Compatible with all existing MR03 stock parts and Option Parts
- Compatible with existing DSM2 and ASF Boards
PNR2.5W INCLUDES
- Main chassis
- Top Deck
- Servo Motor Holder
- Servo Cover
- Battery Clips
- T- Plate spacer
NOTE
Slight modifications to servo cover area is needed to fit the VE and VE Pro boards. (screw hole stands needs to be shaved off)
Compatible with Kyosho Wide Bodies ONLY with side clip minimum spacing of 58MM
Requires existing servo assembly and housing
Instruction Manual Downloadhttp://www.pnracing.com/download/mr3080.pdf
FEATURES:
•Unequal length A-Arm suspension for MR-03 chassis.
–Modeled after full-scale performance car suspension for realism.
–Double A-Arm suspension gives good control of suspension geometry and roll center during travel.
–Camber change with suspension compression during cornering keeps wheels near vertical for maximum tire contact with the road. Allows for precise cornering and maximum road holding.
•Direct suspension swap
–Same width as stock. (MR02/ MR03 PNR2.5W Chassis width)
–Ride height remains the same as stock.
–0.5mm wider front steering geometry for less offset and faster steering. Overall width still remains the same to fit Auto Scale bodies.
•No bump steer throughout suspension travel.
•Suspension movement use ball joints instead of sliding knuckles. Eliminates constriction associated with sliding pin especially with high offset wheels.
–Low constriction results in consistent cornering.
•Machined aluminum ball socket instead of snap-fit. Joints will not pop out even during a hard collision.
•Adjustable camber from 0-3° degrees with 1.3°/mm of camber gain.
•Adjustable caster from 0-1.8° degrees
•4 positions adjustable upper A-Arm pivot
–Changes camber gain, static camber and roll center
–Quick adjustment with set screw
•Includes 3 tie-rods: 0° , +.5° and +1°
•Quick down stop adjustment with the turn of a nut
•Benefits of the sophisticated suspension system are precise cornering and maximum road holding which adds to mini-z driving pleasure
ADJUSTMENT SPEC:
Droop Adjustment
Caster Adjustment
Camber Gain and Camber Adjustment
Tie Rod Adjustment
COMES WITH:
1 x Upper Bracket (#MR3062)
1 x Lower Carbon Plate Cover (MR3070C)
2 x Upper Arm
2 x Lower Arm
4 x Delrin Balls for Upper Arm and Lower Arm (#MR3080D)
2 x Spring Guide Pin (#MR2507)
2 x Spring Holder (#MR2056F)
1 x Full Option Spring Set (#MR2501C)
2 x Knuckle
2 x Knuckle Shaft 3mm (#MR3080A3)
2 x Knuckle Tie Rod Pin
2 x Eccentric Shaft Adjuster (#MR2506)
2 x Lower Arm Pin (#MR2509)
4 x M2-3mm Set Screw (#MR2510S)
1 x 0 Deg Tie Rod (#MR3050G)
1 x +0.5 Tie Rod (#MR3050H)
1 x +1.0 Tie Rod (#MR3050J)
4 x M2-0.2mm Shims (#700501)
2 x M3-0.2mm Shims (#700502)
2 x M2x3 Countersunk Hex Screw (#709903)
2 x M2x4 Countersunk Hex Screw (#709904)
4 x M2x6 Countersunk Hex Screw (#709906)
4 x M2x6 UFO Head Hex Screw (#708806)
2 x M2x10 Countersunk Hex Screw (#709910)
REQUIRED PARTS
4 x Ball Bearing 3x6x2mm #600126
OPTIONAL PARTS
MR3080A2
MR2506F
MR2506FS
MR2506FL
MR3050T
MR3050Q
711906
FEATURES:For MR02 94mm and 98mm wheel base use, use with MR9498 Motor Mount, including top damper mount.INCLUDES:Blue Color3 Spring Set - Blue>Hard Green>Mid Red>SoftDelrin Disk 2pcsPur Fiber Glass Plate 2pcsScrew setsREQUIRES:2mm Lock Nut for top damperTop DamperSilicon Oil
Attention:
This motor mount only working with the motor with 2 screw holes, all Kyosho motor can't install to this motor mount
This is not a complete MR3300 V5 motor mount, this is a motor mount conversion Kit to use with MR3322 Gimbal System
Tri Damper System (TDS) Conversion Kit
ONLY for MR3300 V5 98 Motor MountPacking comes with
2 x Side Damper
1 x Top Damper Plate
1 x Lower Damper Plate
2 x M2x4 Countersunk Screw
4 x M2x8 Countersunk Screw
Requires
MR3300 PN Racing Mini-Z V5 LCG 98mm Motor Mount
MR2161 PN Racing Mini-Z MR015/02 Dual Spring Center Shock Set
MR2162 PN Racing Mini-Z Center Shock Spring Set (7pcs) for adjustment
MR2060, MR2061 or MR2063 Disk Damper System
Gimbals Conversion Kit ONLY for
MR3300 V5 98 Motor Mount, you must use with MR3300G
Packing comes with
1 x Motor Mount Lower Plate
1 x Gimbals T-Mount (Black)
2 x Delrin Ball
2 x Delrin Brushing
1 x Left Lower Holder
1 x Right Lower Holder
1 x M2x4 Countersunk Screw
2 x M2x6 Countersunk Screw
2 x M2x8 Countersunk Screw
Requires
MR3300 PN Racing Mini-Z V5 LCG 98mm Motor Mount
MR3300G Mini-Z Tri Damper System Conversion Kit for MR3300 V5 Motor Mount
MR2161 PN Racing Mini-Z MR015/02 Dual Spring Center Shock Set
MR2162 PN Racing Mini-Z Center Shock Spring Set (7pcs) for adjustment
MR2060, MR2061 or MR2063 Disk Damper System
Instruction Manual Downloadhttp://www.pnracing.com/download/mr3080.pdf
FEATURES:
•Unequal length A-Arm suspension for MR-03 chassis.
–Modeled after full-scale performance car suspension for realism.
–Double A-Arm suspension gives good control of suspension geometry and roll center during travel.
–Camber change with suspension compression during cornering keeps wheels near vertical for maximum tire contact with the road. Allows for precise cornering and maximum road holding.
•Direct suspension swap
–Same width as stock. (MR02/ MR03 PNR2.5W Chassis width)
–Ride height remains the same as stock.
–0.5mm wider front steering geometry for less offset and faster steering. Overall width still remains the same to fit Auto Scale bodies.
•No bump steer throughout suspension travel.
•Suspension movement use ball joints instead of sliding knuckles. Eliminates constriction associated with sliding pin especially with high offset wheels.
–Low constriction results in consistent cornering.
•Machined aluminum ball socket instead of snap-fit. Joints will not pop out even during a hard collision.
•Adjustable camber from 0-3° degrees with 1.3°/mm of camber gain.
•Adjustable caster from 0-1.8° degrees
•4 positions adjustable upper A-Arm pivot
–Changes camber gain, static camber and roll center
–Quick adjustment with set screw
•Includes 3 tie-rods: 0° , +.5° and +1°
•Quick down stop adjustment with the turn of a nut
•Benefits of the sophisticated suspension system are precise cornering and maximum road holding which adds to mini-z driving pleasure
ADJUSTMENT SPEC:
Droop Adjustment
Caster Adjustment
Camber Gain and Camber Adjustment
Tie Rod Adjustment
COMES WITH:
1 x Upper Bracket (#MR3062)
1 x Lower Carbon Plate Cover (MR3070C)
2 x Upper Arm
2 x Lower Arm
4 x Delrin Balls for Upper Arm and Lower Arm (#MR3080D)
2 x Spring Guide Pin (#MR2507)
2 x Spring Holder (#MR2056F)
1 x Full Option Spring Set (#MR2501C)
2 x Knuckle
2 x Knuckle Shaft 3mm (#MR3080A3)
2 x Knuckle Tie Rod Pin
2 x Eccentric Shaft Adjuster (#MR2506)
2 x Lower Arm Pin (#MR2509)
4 x M2-3mm Set Screw (#MR2510S)
1 x 0 Deg Tie Rod (#MR3050G)
1 x +0.5 Tie Rod (#MR3050H)
1 x +1.0 Tie Rod (#MR3050J)
4 x M2-0.2mm Shims (#700501)
2 x M3-0.2mm Shims (#700502)
2 x M2x3 Countersunk Hex Screw (#709903)
2 x M2x4 Countersunk Hex Screw (#709904)
4 x M2x6 Countersunk Hex Screw (#709906)
4 x M2x6 UFO Head Hex Screw (#708806)
2 x M2x10 Countersunk Hex Screw (#709910)
REQUIRED PARTS
4 x Ball Bearing 3x6x2mm #600126
OPTIONAL PARTS
MR3080A2
MR2506F
MR2506FS
MR2506FL
MR3050T
MR3050Q
711906
Attention:
This motor mount only working with the motor with 2 screw holes, all Kyosho motor can't install to this motor mount
This is not a complete MR3300 V5 motor mount, this is a motor mount conversion Kit to use with MR3322 Gimbal System