GL-BT-ESC-060 (without Built-in Bluetooth) Brushless Sensored Speed Control for 1/28 mini car.Change to 32-bit MCU with ultra-smooth, faster response with precise throttle, brake and reverses control.Support ~2.5A BEC ampere drawn which is raised up by ~70%.Support ~30A instant ampere drawn by the motor which is raised up by ~80%.Bluetooth Module for advanced programming and firmware update through the Mobile APPS.APPS will be available on both IOS and Android.Data Analysis through Mobile APPS(Current Input & Output Throttle, Temperature, RPM, Adv. Timing, Voltage and min. voltage, Max Temperature, RPM & Adv. Timing).Software:It is a new developed software with more advanced item functions addedEach item have small step to fine tune. Specifications:Battery Input Voltage: 2S lipoBEC: 6V/2.5A1/28 motor Limit: 9000kv or belowMax Ampere draw: ~30A per phaseSize: ~23.8x14.0x8.7mm(not include the plug)Weight: ~5.6g(without any wire installed)***********************************************************************The corresponding Bluetooth module GL-PC-60 must be ordered separately!Das dazugehörige Bluetooth Modul GL-PC-60 muss separat dazu bestellt werden!***********************************************************************
Manual
Features:
Weight , the MWX chassis is lighter than the GL brass chassis and since most with this car run stock and super stock the heavy weight of the car naturally makes a difference. I basically shifted the weight into better positions to stabilize the handling while calming down the steering making the chassis wide everywhere is not optimal. High level competition has taught me this.
Due to the slightly heavier servo the car requires, I offset some of that Weight with a cutout under the servo.
Each chassis also comes with the infamous FPM (floating pod mount). to further enhance handling.
Instead of being forced to purchase a 50 dollar servo saver by using a sub par rack in the GTR MWX has once again re engineered another GL part to make better for the end user. With this unit you dont have to use the servo saver.
GTR Alu Servo Saver neu mit Verbindungslink aus Aluminium.Wer bereits den GTR Alu Servo Saver (GL-GTR-OP-004) hat, kann diesen mit GL-GTR-OP-031) upgraden.GL-GTR-OP-030 = GL-GTR-OP-004 + GL-GTR-OP-031Installationsanleitung
Speziell für den GL GTR
Technical Specifications:
Model: GL-SD-ESC-010T
Continuous current: 15A
Best Current (10sec): 30A
Battery Input: 3,7 Volt / 2cells, 1.2V NiMh/NiCd / 6cells
Bec output: 6 Volt / 1 A
Weight (without wiring): 4.1g
Dimension (L x W x H) mm: 25 x 15 x 8.5 mm
Mini-Z Motor limit with 2cell x 3.7V Lipo, The motor Timing is at 0 degree: 10000KV or below
Features:
Ultra-smooth, precise trottle and braking control
compatible with sensored/sensorless brushless motors
Data analysis capability (RPM, low voltage and ESC temperature)
Easily Programming throug the LED card (not included)
Built-in one touch On/Off switch with LED
Built-in Low voltage cut-off, Overheat protection and signal loss protection
Included:
Speed Control, Extended BEC wire, Sensor wireDownloads / Manuals (GL-SD-ESC-010T):ESC User GuidelineESC ProgrammierungESC Erklärungen
Während den Sommerferien vom 1. Juli bis zum 10. August 2024 kann die Bearbeitungszeit von Bestellungen 4-5 Tage betragen.
Wir danken euch für euer Verständnis und geniesst den Sommer und das schöne Wetter.