Marka batteries are of high quality and have been developed using the most modern technologies available. They are "Top level" batteries for use in the world of racing at professional levels.These batteries have a high voltage level under load, with a low internal resistance.Designed for use with 1/28 scale car (GLA-GLR-GLF-BZ)   Specification Voltage: 7.4V (2S) Capacity: 350mAh C-rate: 50C Cable: 22Awg Plug: JST-PH Type: Rectangular Size: 44 x 20 x 11.5mm (Length x Width x Height) Weight: 18.5g

Adapterkabel um Lipos mit GL Connector mit dem GL ESC GSC V1.2 zu verwenden.  

Design for charging AAA size batteryFor Nimh (No need to use balance plug)For Li-Ion EP555 with the 4S balance plug

Marka Racing safety lipo bag for charging and storage LiPo batteries. Made from fire-proof and fire-resistant material.The bag is in black color and carries the Marka logo.You can store two standard size batteries.

High Voltage 2S battery for R/C Competition usage. Size fit for GL-RIDER, GLA ,GLR, GLF-1

High Voltage 2S battery for R/C Competition usage. Size fit for GL-RIDER, GLA ,GLR, GLF-1

200-200-Ladegerät mit Display für RC-Akkus Zum Laden/Entladen von 1-6S LiPo-, LiFe-, LiHV-, Li-Ion- sowie 1-16S NiMH/NiCd- und 1-12S Blei(Pb)-Akkus Einstellbarer Ladestrom von 0.1 bis 8.0 A und Entladestrom von 0.1 bis 1.0 A Ladeleistung: AC 50 W / DC 200 W Einfache Bedienung mittels Drehknopf Abnehmbares Netzteil Unterstützt BattGO-Akkutechnologie

Produktinformationen "3x GL connector Parallel Charging Cable" [PT0006] 3x GL connector Parallel Charging Cable Details: 3x JST-PH Parallel charging cable For GLA and Atomic AMZ/BZ Lipo batteries or any other 2S Lipo with a JST-PH connector. This handy charge cable allows you to connect 4mm banana plugs to chargers, and the charger's balance board. On the battery side, we have provided 3x JST-PH connectors so that you can charge/discharge up to 3 packs at a time. You do not have to use all 3 of course, using it to charge 1 pack is perfectly fine, but if you would like charge/discharge up to 3 packs together, this cable can do it. For those new to parallel charging, you can google/you tube information on it, but in summary: You can only connect 2S Lipo to this cable Mixing 300mAh, 330mAh, 360mAh together is ok The packs should be reasonably similar in voltage, for example, 2 packs 90% full, 1 pack empty, is NOT such a good idea, as it will cause a lot of current(Amps) going from the full packs to the empty pack, charging the empty pack at very high current(AMps), this might even melt the cable if the Packs are large/high C enough. All empty is fine, ~30%, ~40%, ~50% mix together is fine. Ideally charger capacity set to total mAh of the packs Charger current can scale up according to total capacity of the packs

Receiver Cable (RX cable) Compatible with Swave-E2 & Swave-W & W2 ONLY Cannot use on Swave-E 1.0mm JST to 1.5mm JST Wire length: 80mm ** Some aftermarket / no-brand receiver may require swap the cable you will need to consult your receiver seller.

Package Included: 2 x JST-PH connector power cable

These batteries have a high voltage level under load, with low internal resistance.Designed for use with PNR2.5W chassis and Kyosho MR03 Chassis. (This is a thin version, you can add on some lead on your chassis to add weight) SpecificationVoltage: 3.75V (1S)Capacity: 380mAhRecommend Charge Rate: 0.8AC-rate: 60C Cable: 24Awg Plug: Molex Size: 42.6 x 20 x 6.2mm (Length x Width x Height) Weight: 9g

New HP750 batteries provide high voltage output over time Recommend charge at 0.7-1.0amp for the best balance between power and run time.   Specifications 750mah capacity AAA size 4pcs

Racing Power Batteries rp747 Stock spec for MiniZ. if you want more punch than rp900 this is your battery, more punch but less runing time. Perfect to be used in Stock class.

3x JST-PH Parallel charging cable For GLA and Atomic AMZ/BZ Lipo batteries or any other 2S Lipo with a JST-PH connector. This handy charge cable allows you to connect 4mm banana plugs to chargers, and the charger's balance board. On the battery side, we have provided 3x JST-PH connectors so that you can charge/discharge up to 3 packs at a time. You do not have to use all 3 of course, using it to charge 1 pack is perfectly fine, but if you would like charge/discharge up to 3 packs together, this cable can do it. For those new to parallel charging, you can google/you tube information on it, but in summary: You can only connect 2S Lipo to this cable Mixing 300mAh, 330mAh, 360mAh together is ok The packs should be reasonably similar in voltage, for example, 2 packs 90% full, 1 pack empty, is NOT such a good idea, as it will cause a lot of current(Amps) going from the full packs to the empty pack, charging the empty pack at very high current(AMps), this might even melt the cable if the Packs are large/high C enough. All empty is fine, ~30%, ~40%, ~50% mix together is fine. Ideally charger capacity set to total mAh of the packs Charger current can scale up according to total capacity of the packs Below is a good video guide: https://www.youtube.com/watch?v=WY194Md6KNg