Attention:
This motor mount only working with the motor with 2 screw holes, all Kyosho motor can't install to this motor mount
This is not a complete MR3300 V5 motor mount, this is a motor mount conversion Kit to use with MR3322 Gimbal System
This is SPEC Gearing 64P 10T Pinion/64P 53T Spur Gearfor PNWC Super Stock ClassORANGE RING COLOR for Tech Inspection easierComes with 0.9mm wrench64 Pitch only for PN 64 Pitch Spur Gear use
This is SPEC Gearing 64P 14T Pinion/64P 53T Spur Gearfor PNWC GTLM Super Stock Class
RED RING COLOR for Tech Inspection easier
Comes with 0.9mm wrench
64 Pitch only for PN 64 Pitch Spur Gear use
Comes with 0.9mm wrench64 Pitch only for PN 64 Pitch Spur Gear use
This is SPEC Gearing 64P 16T Pinion/64P 53T Spur Gear for PNWC 2WD Stock ClassBlue RING COLOR for Tech Inspection easier
We are proud to introduce the all new PNR2.5W after close to 2 years of design and testing. PNR2.5W is the must have DIRECT replacement for all existing Mini-Z MR03 chassis.
Engineered and design ground up by World Champions, the chassis is made of Nylon with fiberglass and ABS material. PNR 2.5W has
- Lower Battery CG
- Hard Coating Battery Terminals
- Better heat dissipation for batteries and electronics
- Lighter and Wider chassis to provide superb stability
- Ample top deck space to allow 3rd party receivers
- Compatible with all existing MR03 stock parts and Option Parts
- Compatible with existing DSM2 and ASF Boards
PNR2.5W INCLUDES
- Main chassis
- Top Deck
- Servo Motor Holder
- Servo Cover
- Battery Clips
- T- Plate spacer
NOTE
Slight modifications to servo cover area is needed to fit the VE and VE Pro boards. (screw hole stands needs to be shaved off)
Compatible with Kyosho Wide Bodies ONLY with side clip minimum spacing of 58MM
Requires existing servo assembly and housing
PN Racing Servo Saver- Spring rate 20% stiffer than Kyosho - Made by Delrin- "K" marked link for Kyosho MR03 with SHORT stainless steel pin- "P" marked link for PN Chassis 900300 with LONG stainless steel pin
Includes:
64 Pitch Ball Diff with 53T Spur Gear
64 Pitch Pinion 9-14T
Spec Data:
NEW Ti color Light Weight Alm 7075 Shaft (MR2045UL)
10pcs Ceramic Ball
High quality O-ring, made in Japan
Ball Bearing build in
Ultra V3 0.8mm Ti Gold D-Cut Pressure Plate (MR2049T)
New Delrin O-Ring Holder not easy to loss
Spur Gear for PN Racaing Gear Diff
For replacement PN Racing Mini-Z Precision Gear Differential Spur Gear
Changing Spur Gear Ratio
Loosen Tension Nut to separate side gears.
Allow spider gear pins to recess into carrier. Depress with screw driver if necessary as shown by arrows.
Remove spur gear.
Installation is reverse of removal
OFFICIAL PNWC Spur Gear for 2WD Stock class and Super Stock class
For replacement PN Racing Mini-Z Precision Gear Differential Spur Gear
Changing Spur Gear Ratio
Loosen Tension Nut to separate side gears.
Allow spider gear pins to recess into carrier. Depress with screw driver if necessary as shown by arrows.
Remove spur gear.
Installation is reverse of removal
Work for MR02 Stock front end, MR02 (MR2500) and MR03 (MR3050) PN Double A arm
Comes with:
Lip thickness 0.8mm
2 x 4.8mm height Delrin Machine Cut Spring Holder
2 x 5.0mm height Delrin Machine Cut Spring Holder
2 x 5.2mm height Delrin Machine Cut Spring Holder
4 x 0.2mm Shims (Orange)
4 x 0.5mm Shims (Blue)
FEATURES:For MR02 94mm and 98mm wheel base use, use with MR9498 Motor Mount, including top damper mount.INCLUDES:Blue Color3 Spring Set - Blue>Hard Green>Mid Red>SoftDelrin Disk 2pcsPur Fiber Glass Plate 2pcsScrew setsREQUIRES:2mm Lock Nut for top damperTop DamperSilicon Oil
Center spring helps to off load weight of car from T-plate. T-plate can stay flat with no curvature.
This gives the T-plate maximum freedom to twist for consistent roll control and better traction.
Thru-shaft design maximize length of cylinder for smooth operation.
Extra cylinder surface area increase effectiveness of damping oil or grease when used.
Thru-shaft arrangement also results in constant amount of overlap between shaft and cylinder for consistent damping thru out travel.
Adjustable coil over shock spring
Adjustable negative spring. Addition of negative spring controls the shock during bottoming.
It dampens rebound for better axel control, and minimize momentary traction loss when going over large bumps.
Negative spring interchangeable with MR02 front springs.
Therefore wide range of springs can be used for tuning.
Optional Spring set MR2162 buy separate.
Use for MR2990 Side Shock (Short Version) optional spring replacement: Also work on PN Tri Damper System Short version good for set up 94mm mount. Yellow > White > Purple > Green > Red
Der flexibelste Motorenhalter von PN Racing mit einstellbarem Radstand von 93 - 102 mm.Features:
Compatible with PNR2.5W, MR015, MR02 and MR03
Wheelbase adjustable from 93mm to 102mm in 1mm increment. Include both 93-102mm standard width and optional parts MR2395D 98-102mm LM width Differential Carrier.
Wheelbase adjusted with only 2 screws.
Wheelbase adjustment does not affect gear mesh or suspension set-up. Allows quick testing of different wheelbase at the track.
Motor drops down for adjustment without affecting suspension set-up especially on a tri-damper set-up.
Multiple motor height positions possible for all track surfaces.
Four ride height adjustments with 2 eccentric bearing holders.
The ultimate motor mount. Results of years of improvement to Mini-Z motor mount designs.
Attention:This motor mount only working with the motor with 2 screw holes, all Kyosho motor can't install to this motor mount
Der flexibelste Motorenhalter von PN Racing mit einstellbarem Radstand von 93 - 102 mm.Features:
Compatible with PNR2.5W, MR015, MR02 and MR03
Wheelbase adjustable from 93mm to 102mm in 1mm increment. Include both 93-102mm standard width and optional parts MR2395D 98-102mm LM width Differential Carrier.
Wheelbase adjusted with only 2 screws.
Wheelbase adjustment does not affect gear mesh or suspension set-up. Allows quick testing of different wheelbase at the track.
Motor drops down for adjustment without affecting suspension set-up especially on a tri-damper set-up.
Multiple motor height positions possible for all track surfaces.
Four ride height adjustments with 2 eccentric bearing holders.
The ultimate motor mount. Results of years of improvement to Mini-Z motor mount designs.
Attention:This motor mount only working with the motor with 2 screw holes, all Kyosho motor can't install to this motor mount
High-precision machine cut Black Delrin 64P Extra length 10.5mm to keep the pinion on the motor shaft#PN-MR2709 9T#PN-MR2710 10T#PN-MR2711 11T#PN-MR2712 12T#PN-MR2713 13T#PN-MR2714 14T#PN-MR2715 15T#PN-MR2716 16T
High-precision machine cut Black Delrin 64P Extra length 10.5mm to keep the pinion on the motor shaft#PN-MR2709 9T#PN-MR2710 10T#PN-MR2711 11T#PN-MR2712 12T#PN-MR2713 13T#PN-MR2714 14T#PN-MR2715 15T#PN-MR2716 16T
High-precision machine cut Black Delrin 64P Extra length 10.5mm to keep the pinion on the motor shaft#PN-MR2709 9T#PN-MR2710 10T#PN-MR2711 11T#PN-MR2712 12T#PN-MR2713 13T#PN-MR2714 14T#PN-MR2715 15T#PN-MR2716 16T
High-precision machine cut Black Delrin 64P Extra length 10.5mm to keep the pinion on the motor shaft#PN-MR2709 9T#PN-MR2710 10T#PN-MR2711 11T#PN-MR2712 12T#PN-MR2713 13T#PN-MR2714 14T#PN-MR2715 15T#PN-MR2716 16T