19,00 CHF*
Artikel-Nr.:
AGF-SPV3
Ab CH Lager verfügbar, Lieferzeit 2-5 Tage
Produktinformationen "AGF-RC SPV3 USB Program Card for AGF-RC Programmable Servos"
Optionales USB Interface zum programmieren von dafür geeigneten AGF-RC Servos
Hierzu ist ein Windows Computer erforderlich mit Windows 7 oder 10. Die Servos werden direkt über den USB Port versorgt und müssen nur in das Interface gesteckt werden. In der Software kann zum Beispiel der Softstart, der Neutralpunkt, die Servowege angepasst (größer und kleiner) oder die Drehrichtung eingestellt werden. Des weiteren kann falls benötigt der Sanwa SSR Mode aktiviert werden was besonders für RC-Car Fahrer von Interesse ist. Ebenfalls kann die integrierte Überlastabschaltung in 3 Stufen angepasst werden und ausgewählt werden was bei einem Signalverlust passiert soll.
Bitte beachten Sie das die Software aktuell nur Englisch ist!
Hierzu ist ein Windows Computer erforderlich mit Windows 7 oder 10. Die Servos werden direkt über den USB Port versorgt und müssen nur in das Interface gesteckt werden. In der Software kann zum Beispiel der Softstart, der Neutralpunkt, die Servowege angepasst (größer und kleiner) oder die Drehrichtung eingestellt werden. Des weiteren kann falls benötigt der Sanwa SSR Mode aktiviert werden was besonders für RC-Car Fahrer von Interesse ist. Ebenfalls kann die integrierte Überlastabschaltung in 3 Stufen angepasst werden und ausgewählt werden was bei einem Signalverlust passiert soll.
Bitte beachten Sie das die Software aktuell nur Englisch ist!
----------------------------------------------------
Software download from here: Download Software
you can download the ".exe" file directly or zip file as required.
System Requirement
- Operating Voltage: USB(5V/500mA)
- Operating System: Windows XP/Windows Vista/Windows 7/Windows 8 /windows10 ( 32/64bit).
- Application: AGFrc Programmable Servos with ASSmarked.
Parameter Function Instruction
1. Servo Angle: Set the servo rotation angle
2. Servo Neutral: Set the servo neutral position
Note: While the transmitter turn to the neutral position, if the servo do not stay in the corresponding position, it can modify this value to adjust the servo horn. This is equivalent to the trimming of transmitter channel.
3. PWM Power: Adjust the servo output power. The higher the power, the higher the servo torque and speed, current consumption will be high as well.
4. Damping Factor: Set the servo damping.
5. Sensitivity: Adjust the servo dead band (sensitivity).
6. Soft Start: Slowly restoration while power on the servo. Once power on, the servo will gently turn to the position of current input signal.
Note: This function is to prevent damage from servo incorrect mounting while power on.
7. Inversion: Set normal and reverse rotation of the servo.
8. Narrow Band: FUTABA SR Mode
9. SANWA SSR: SANWA SSR Mode
Note: Enable this function, it can support SANWA SSR high speed mode. Servo angle may be not accurate, it need to re-adjust.
10. Lost PPM Protect: Signal loss protection, there are three functions for selection,
a. Release: Non-Protection
b. Keep Position: Stay in the position before the signal loss
c. Go Neutral Position: Back to Neutral position (1500uS position)
11. Over Load Protect: Set the servo blocking protection, there are three levels, ticked to enable protection.
Level 1: Set the starting time and power value of the primary protection.
Level 2: Set the starting time and power value of the secondary protection.
Level 3: Set the starting time and power value of the tertiary protection.
Note: Left side is to set the protection starting time, right side is to set output power value after enable starting protection.
12. Servo Information: Servo information. Including servo model, version date, firmware name.
Servo Name: Servo model
Manufacture: Servo version date
Firmware: Servo firmware name
13. Read: Read the servo parameter from the software interface.
14. Write: Write current parameter into servo.
15. Open: Open servo parameter file which saved on the computer.
16. Save: Save current servo parameter to the computer
17. UPF: Servo firmware upgrade function.
18. Default: Restore factory defaults.
19. Exit: Exit and close the configuration software
Anmelden