GL-BT-ESC-030 (Built-in Bluetooth) Brushless Sensored Speed Control for 1/28 mini car Change to 32-bit MCU with ultra-smooth, faster response with precise throttle,brake and reverses control. Support ~2.5A BEC ampere drawn which is raised up by ~70%. Support ~30A instant ampere drawn by the motor which is raised up by ~80%.Built-in Bluetooth device for advanced programming and firmware update through the Mobile APPS.APPS will be available on both IOS and Android.Real Time Data Analysis through Mobile APPS (Current Input & Output Throttle, Temperature, RPM, Adv. Timing, Voltage and min. voltage, Max Temperature, RPM & Adv. Timing). Software: It is a new developed software with more advanced item functions added.Each item have small step to fine tune. All update item functions information can be reviewed from the photos attached. Specs: Battery Input Voltage: 2S lipo BEC: 6V/2.5A
1/28 motor Limit: 9000kv or below
Max Ampere draw: ~30A per phase
Size: ~22.7x14.0x9.6mm (not include the plug)
Weight: ~5.6g(without any wire installed)Download Manual
GL-BT-ESC-030-GTR(Built-in Bluetooth) Brushless Sensored Speed Control for 1/28 mini car *** Spezielle Variante für das GL GTR Chassis ***Change to 32-bit MCU with ultra-smooth, faster response with precise throttle,brake and reverses control. Support ~2.5A BEC ampere drawn which is raised up by ~70%. Support ~30A instant ampere drawn by the motor which is raised up by ~80%.Built-in Bluetooth device for advanced programming and firmware update through the Mobile APPS.APPS will be available on both IOS and Android.Real Time Data Analysis through Mobile APPS (Current Input & Output Throttle, Temperature, RPM, Adv. Timing, Voltage and min. voltage, Max Temperature, RPM & Adv. Timing). Software: It is a new developed software with more advanced item functions added.Each item have small step to fine tune. All update item functions information can be reviewed from the photos attached. Specs: Battery Input Voltage: 2S lipo BEC: 6V/2.5A
1/28 motor Limit: 9000kv or below
Max Ampere draw: ~30A per phase
Size: ~22.7x14.0x9.6mm (not include the plug)
Weight: ~5.6g(without any wire installed)Download Manual
Sensorkabel passend für ESC:- GL-SD-ESC-010T
- GL-SD-ESC-020T
- GL-SD-ESC-030T- Hobbywing Mini28für GL Motoren mit dem neuen, kleinen Sensorkabelanschluss
(For GTR, GLA, GLR ,GLF, GL-RIDER)
Technical Specifications:
Model: GL-SD-ESC-010T
Continuous current: 15A
Best Current (10sec): 30A
Battery Input: 3,7 Volt / 2cells, 1.2V NiMh/NiCd / 6cells
Bec output: 6 Volt / 1 A
Weight (without wiring): 4.1g
Dimension (L x W x H) mm: 25 x 15 x 8.5 mm
Mini-Z Motor limit with 2cell x 3.7V Lipo, The motor Timing is at 0 degree: 10000KV or below
Features:
Ultra-smooth, precise trottle and braking control
compatible with sensored/sensorless brushless motors
Data analysis capability (RPM, low voltage and ESC temperature)
Easily Programming throug the LED card (not included)
Built-in one touch On/Off switch with LED
Built-in Low voltage cut-off, Overheat protection and signal loss protection
Included:
Speed Control, Extended BEC wire, Sensor wireDownloads / Manuals (GL-SD-ESC-010T):ESC User GuidelineESC ProgrammierungESC Erklärungen
Speziell für den GL GTR
Technical Specifications:
Model: GL-SD-ESC-010T
Continuous current: 15A
Best Current (10sec): 30A
Battery Input: 3,7 Volt / 2cells, 1.2V NiMh/NiCd / 6cells
Bec output: 6 Volt / 1 A
Weight (without wiring): 4.1g
Dimension (L x W x H) mm: 25 x 15 x 8.5 mm
Mini-Z Motor limit with 2cell x 3.7V Lipo, The motor Timing is at 0 degree: 10000KV or below
Features:
Ultra-smooth, precise trottle and braking control
compatible with sensored/sensorless brushless motors
Data analysis capability (RPM, low voltage and ESC temperature)
Easily Programming throug the LED card (not included)
Built-in one touch On/Off switch with LED
Built-in Low voltage cut-off, Overheat protection and signal loss protection
Included:
Speed Control, Extended BEC wire, Sensor wireDownloads / Manuals (GL-SD-ESC-010T):ESC User GuidelineESC ProgrammierungESC Erklärungen
Spare gear set for Graupner DES131 servo.
They don't break that easily, but it can happen, if your DES131 is broken, open it and check if one of the gears is broken, if so, this is what you need to fix it.
For GLA and GLA-V2
For GLA-V2, GLR, GLR-GT, GL-Drift-2022, GLF-1, GL-RIDERArtikelbezeichnung: GL003-DMG
Alternative Artikelnummern: GL-Drift-S-025, GL-GT-S-035, GLF-S-016
Features:
Alloy Top and Bottom Casing
Full Metal gears
Dual Bearing
Speed: 0.06sec/ 60° @ 6.0V
Torque: 1.10 kg . cm @ 6.0V
Weight: 5g
- linear power control.- High efficiency of energy conversion.- Better torque than Kyosho VE motor series.- JAPAN high quality duel ball Bearing included.- no power fade at higher temperatures.- 15mm diameter.
Motor developed with GLA in mind, enough power for experienced usersMore power - a little more powerful than PN5500, but less than PN7500Easier to control - with a more linear power band making your car easier to control.Longer run time - it also boast higher electrical efficiency than motors of the same classPowerful til the end - Power level stays more consistent towards the end of each run, but this does mean that motor feels hotter at the end of run, because it stayed at high power levels until the very end.Taller gear ratios - recommended GLA gear ratio from 5.4 to 6.1 depending on your driving style and track layoutTIP: Wiring is reverse to PN, so if you are swapping out a PN, swap any 2 of the 3 motor wires
GL High-Torque Brushless Motor (8600KV)
Motor developed with NiMH Mini-Zs as well as GLA in mind, very high power for expert users
More power - one of the most powerful motors out there, due to its High Torque, KV rating is not high, but more poweful than some higher KV motors on market
Easier to control - with a more linear power band making your car easier to control.
Longer run time - it also boast higher electrical efficiency than motors of the same class
Powerful til the end - Power level stays more consistent towards the end of each run, but this does mean that motor feels hotter at the end of run, because it stayed at high power levels until the very end.
Taller gear ratios - recommended GLA gear ratio from 8.2 to 9.5 depending on your driving style and track layout
TIP: Wiring is reverse to PN, so if you are swapping out a PN, swap any 2 of the 3 motor wires
Variante ohne GehäuseFeatures
Modulation:Compatible Kyosho-FHSSSmall size: 21.5*14.6*6.5mm(not including antenna)Super light: 2.4g(including antenna)Working voltage:3.7~8.4VHigh performance CPU enhance exactness control feeling4 channel supportAdded failsafe functionIdeal for any micro RC racing chassisComes with 3P 1.5mm plug
Kompatible Fernsteuerungen
KYOSHO KT-432PTKYOSHO KT-531P
FLYSKY NB4 NANO 4CH TOWER ANTENNA RECEIVERVariante mit CNC-Gehäuse! Description:This 2.4G RC receiver uses AFHDS3 protocol and it is dedicated to the FLYSKY Noble NB4 transmitter. It has single-antenna, use two-way transmission and features a unique compact design that saves space. Features:1. FLYSKY AFHDS3 protocol compatible2. High performance CPU enhance precision control feeling3. 4 channel servo signal4. Tower antenna provides both good receipt signal and space saving5. Nano size (19mm x 12mm)6. Added failsafe function7. Operating Voltage 3.5V - 12V8. Weight: 3g Binding:1. Press the BIND button and power on the receiver, the receiver’s led will flash quickly.2. Put the transmitter into bind mode. The receiver’s led will flash slowly when the binding is successful.3. Disconnect receiver’s power and reconnect the power cable to the receiver. Now is should working normally. Compatible Transmitters:FLYSKY Noble NB4FLYSKY Noble NB4 ProFLYSKY PL18 Package Included:1 x Receiver4 x 1.5mm 3P JST plug with high quality silicon cable
FLYSKY NB4 NANO 4CH TOWER ANTENNA RECEIVERVariante ohne Gehäuse! Description:This 2.4G RC receiver uses AFHDS3 protocol and it is dedicated to the FLYSKY Noble NB4 transmitter. It has single-antenna, use two-way transmission and features a unique compact design that saves space. Features:1. FLYSKY AFHDS3 protocol compatible2. High performance CPU enhance precision control feeling3. 4 channel servo signal4. Tower antenna provides both good receipt signal and space saving5. Nano size (19mm x 12mm)6. Added failsafe function7. Operating Voltage 3.5V - 12V8. Weight: 3g Binding:1. Press the BIND button and power on the receiver, the receiver’s led will flash quickly.2. Put the transmitter into bind mode. The receiver’s led will flash slowly when the binding is successful.3. Disconnect receiver’s power and reconnect the power cable to the receiver. Now is should working normally. Compatible Transmitters:FLYSKY Noble NB4FLYSKY Noble NB4 ProFLYSKY PL18 Package Included:1 x Receiver4 x 1.5mm 3P JST plug with high quality silicon cable
FLYSKY NB4 NANO 4CH TOWER ANTENNA RECEIVERVariante mit PVC Gehäuse! Description:This 2.4G RC receiver uses AFHDS3 protocol and it is dedicated to the FLYSKY Noble NB4 transmitter. It has single-antenna, use two-way transmission and features a unique compact design that saves space. Features:1. FLYSKY AFHDS3 protocol compatible2. High performance CPU enhance precision control feeling3. 4 channel servo signal4. Tower antenna provides both good receipt signal and space saving5. Nano size (19mm x 12mm)6. Added failsafe function7. Operating Voltage 3.5V - 12V8. Weight: 3g Binding:1. Press the BIND button and power on the receiver, the receiver’s led will flash quickly.2. Put the transmitter into bind mode. The receiver’s led will flash slowly when the binding is successful.3. Disconnect receiver’s power and reconnect the power cable to the receiver. Now is should working normally. Compatible Transmitters:FLYSKY Noble NB4FLYSKY Noble NB4 ProFLYSKY PL18 Package Included:1 x Receiver4 x 1.5mm 3P JST plug with high quality silicon cable
This RC receiver unit is FUTABA T-FHSS SR compatible. It offers full 4-channel support in ultra-light weight and micro size.> with CNC Metal CaseFeatures:Futaba 2.4GHz T-FHSS SR CompatibleHigh performance CPU enhance precision control feeling.4 channel supportNano size (19mm x 12mm)Added failsafe functionOperating Voltage 3.5V - 12VWeight: 3gLink Procedure:Each transmitter has an individually assigned, unique ID code. In order to start operation, the receiver must be linked with the ID code of the transmitter with which it is being paired. Once the link is made the ID code is stored in the receiver and no further linking is necessary unless the receiver is to be used with another transmitter.1-Place the transmitter and the receiver close to each other within half (0.5) meter.2-Place the transmitter into the linking mode and turn on the receiver3-During countdown, push the receiver tact switch for approximately 2 seconds. The LED will begin to blink red. After the receiver LED switches from blinking red to green - red steady light, If the transmitter and receiver are linked normally, set the power switch to the OFF position and then turn on the PWR ON position. If the receiver LED lights green, linking was succeeded. Actually check servo operation.Normal mode / High Speed mode:The‘Normal mode’accepts any type of servos or the peripheral. The "High Speed mode" only accepts the digital servos, including BLS series, and most peripheral equipment such as the brushless ESCs. Please pay special attention to the information contained within this manual and transmitter manual in order to have a pleasant running experience.Compatible Transmitters:FUTABA 10PXFUTABA 7PXFUTABA 7PXRFUTABA 7XCFUTABA 4PMFUTABA 4PXFUTABA 4PXRFUTABA 4PLFUTABA 4PLSFUTABA 4PVFUTABA 4GRSFUTABA 3PVPackage Included:1 x Receiver4 x 1.5mm 3P JST plug with high quality silicon cable
This RC receiver unit is FUTABA T-FHSS SR compatible. It offers full 4-channel support in ultra-light weight and micro size.> with PVC CaseFeatures:Futaba 2.4GHz T-FHSS SR CompatibleHigh performance CPU enhance precision control feeling.4 channel supportNano size (19mm x 12mm)Added failsafe functionOperating Voltage 3.5V - 12VWeight: 3gLink Procedure:Each transmitter has an individually assigned, unique ID code. In order to start operation, the receiver must be linked with the ID code of the transmitter with which it is being paired. Once the link is made the ID code is stored in the receiver and no further linking is necessary unless the receiver is to be used with another transmitter.1-Place the transmitter and the receiver close to each other within half (0.5) meter.2-Place the transmitter into the linking mode and turn on the receiver3-During countdown, push the receiver tact switch for approximately 2 seconds. The LED will begin to blink red. After the receiver LED switches from blinking red to green - red steady light, If the transmitter and receiver are linked normally, set the power switch to the OFF position and then turn on the PWR ON position. If the receiver LED lights green, linking was succeeded. Actually check servo operation.Normal mode / High Speed mode:The‘Normal mode’accepts any type of servos or the peripheral. The "High Speed mode" only accepts the digital servos, including BLS series, and most peripheral equipment such as the brushless ESCs. Please pay special attention to the information contained within this manual and transmitter manual in order to have a pleasant running experience.Compatible Transmitters:FUTABA 10PXFUTABA 7PXFUTABA 7PXRFUTABA 7XCFUTABA 4PMFUTABA 4PXFUTABA 4PXRFUTABA 4PLFUTABA 4PLSFUTABA 4PVFUTABA 4GRSFUTABA 3PVPackage Included:1 x Receiver4 x 1.5mm 3P JST plug with high quality silicon cable
This RC receiver unit is FUTABA F-4G compatible. It offers full 4-channel support in ultra-light weight and micro size.> with PVC CaseFeatures:Futaba F-4G ompatibleHigh performance CPU enhance precision control feeling.4 channel supportNano size (19mm x 12mm)Added failsafe functionOperating Voltage 3.5V - 12VWeight: 3gLink Procedure:Each transmitter has an individually assigned, unique ID code. In order to start operation, the receiver must be linked with the ID code of the transmitter with which it is being paired. Once the link is made the ID code is stored in the receiver and no further linking is necessary unless the receiver is to be used with another transmitter.1-Place the transmitter and the receiver close to each other within half (0.5) meter.2-Place the transmitter into the linking mode and turn on the receiver3-During countdown, push the receiver tact switch for approximately 2 seconds. The LED will begin to blink red. After the receiver LED switches from blinking red to green - red steady light, If the transmitter and receiver are linked normally, set the power switch to the OFF position and then turn on the PWR ON position. If the receiver LED lights green, linking was succeeded. Actually check servo operation.Normal mode / High Speed mode:The‘Normal mode’accepts any type of servos or the peripheral. The "High Speed mode" only accepts the digital servos, including BLS series, and most peripheral equipment such as the brushless ESCs. Please pay special attention to the information contained within this manual and transmitter manual in order to have a pleasant running experience.Compatible Transmitters:FUTABA 10PXPackage Included:1 x Receiver4 x 1.5mm 3P JST plug with high quality silicon cable
SANWA NANO 4CH TOWER ANTENNA RECEIVERModel mit CNC Metal Gehäuse Description:This RC receiver unit is Sanwa FHSS-4 and FHSS-3 compatible. It offers full 4-channel support in ultra-light weight and micro size. Features:1. Sanwa 2.4GHz FH3/FH4 Selectable Via Transmitter2. High performance CPU enhance precision control feeling3. 4 channel support4. Micro size (19mm x 12mm)5. Added failsafe function6. Operating Voltage 3.5V - 12V7. Weight: 3g Binding:1. Press the BIND button and power on the receiver, the receiver’s led will flash quickly.2. Put the transmitter into bind mode. The receiver’s led will flash slowly when the binding is successful.3. Disconnect receiver’s power and reconnect the power cable to the receiver. Now is should working normally. Compatible Transmitters:Sanwa M17Sanwa M12SSanwa M12Sanwa MT44Sanwa MT4SSanwa MT4Sanwa M11X Package Included:1 x Receiver4 x 1.5mm 3P JST plug with high quality silicon cable
SANWA NANO 4CH TOWER ANTENNA RECEIVERModel ohne Gehäuse Description:This RC receiver unit is Sanwa FHSS-4 and FHSS-3 compatible. It offers full 4-channel support in ultra-light weight and micro size. Features:1. Sanwa 2.4GHz FH3/FH4 Selectable Via Transmitter2. High performance CPU enhance precision control feeling3. 4 channel support4. Micro size (19mm x 12mm)5. Added failsafe function6. Operating Voltage 3.5V - 12V7. Weight: 3g Binding:1. Press the BIND button and power on the receiver, the receiver’s led will flash quickly.2. Put the transmitter into bind mode. The receiver’s led will flash slowly when the binding is successful.3. Disconnect receiver’s power and reconnect the power cable to the receiver. Now is should working normally. Compatible Transmitters:Sanwa M17Sanwa M12SSanwa M12Sanwa MT44Sanwa MT4SSanwa MT4Sanwa M11X Package Included:1 x Receiver4 x 1.5mm 3P JST plug with high quality silicon cable
SANWA NANO 4CH TOWER ANTENNA RECEIVERModel mit PVC Gehäuse Description:This RC receiver unit is Sanwa FHSS-4 and FHSS-3 compatible. It offers full 4-channel support in ultra-light weight and micro size. Features:1. Sanwa 2.4GHz FH3/FH4 Selectable Via Transmitter2. High performance CPU enhance precision control feeling3. 4 channel support4. Micro size (19mm x 12mm)5. Added failsafe function6. Operating Voltage 3.5V - 12V7. Weight: 3g Binding:1. Press the BIND button and power on the receiver, the receiver’s led will flash quickly.2. Put the transmitter into bind mode. The receiver’s led will flash slowly when the binding is successful.3. Disconnect receiver’s power and reconnect the power cable to the receiver. Now is should working normally. Compatible Transmitters:Sanwa M17Sanwa M12SSanwa M12Sanwa MT44Sanwa MT4SSanwa MT4Sanwa M11X Package Included:1 x Receiver4 x 1.5mm 3P JST plug with high quality silicon cable
Color: BlackDSK-701 2.4GHz 4-Channel FHSS5 SSL Telemetry Receiver uses a tower antenna with exceptional range and response time. With a lightweight design and a small footprint, this receiver is great for Mini-z scale electric RC cars. Features:1. Sanwa 2.4GHz FHSS5U/FHSS5 Spread Spectrum System compatible2. Compatible with SSL (SUPER VORTEX Series, etc...)3. Ultra Response Mode (SUR)4. Extreme Response Mode (SXR)5. Dual ID system (able to bind with 2 transmitters)6. Micro size (19mm x 12 mm)7. Operating Voltage 3.5V - 8.4V8. Weight: 2g Indicator Function compatible:Indicator function can be checked signal strength connected transmitter. The indicator function can be used for finding problems as incorrect receiver placing and finding the best receiver position for transmitter. Indicator function can be checked signal strength without any effect with response. NOTE:RPM sensor (SNW107A41061A) and temperature sensor are not compatibleRPM and temperature telemetry are only capable with the Sanwa Super Vortex seriesFH5U RF mode is not capable to use telemetrySXR response mode is only compatible with transmitter M17. Compatible Transmitters:Sanwa M17Sanwa MT-5Sanwa MT-R Package Included:1 x Receiver (Farbe: Schwarz)Bind:1.Turn on transmitter, enter [BIND] to be bind mode.2.Connect BIND plug in BIND port then turn on receiver.3.LED will change from slow flashing blue to fast flashing blue.4.Turn off receiver, remove BIND plug, then turn on.5.Finish BIND mode on transmitter.