All new from Reflex Racing is our precision high speed CNC lathe-turned set up wheels. Made without bearings and a deep dish to make it compatible with all 2WD and AWD cars that use a 3mm Axle. The elimination of the bearings in the wheel make the fit with much tighter tolerances, which allows for a more precise camber setting when being used with our RX28A-31 Camber Gauge.Lieferumfang:- 1 Paar
The Wing Things are designed to make mounting your wing much easier. Install the screw from the bottom of the body and thread them into the wing thing threads. You can hold the wing thing with a 4.5mm hex wrench to fully tighten.
The total weight of the 2 wing things and 2 M2x4 is roughly 0.5g; about the same weight as using a couple of steel hex nuts and 6mm steel screws that are typically included in body sets.
The Wing Things are designed to make mounting your wing much easier. Install the screw from the bottom of the body and thread them into the wing thing threads. You can hold the wing thing with a 4.5mm hex wrench to fully tighten.
The total weight of the 2 wing things and 2 M2x4 is roughly 0.5g; about the same weight as using a couple of steel hex nuts and 6mm steel screws that are typically included in body sets.
The Wing Things are designed to make mounting your wing much easier. Install the screw from the bottom of the body and thread them into the wing thing threads. You can hold the wing thing with a 4.5mm hex wrench to fully tighten.
The total weight of the 2 wing things and 2 M2x4 is roughly 0.5g; about the same weight as using a couple of steel hex nuts and 6mm steel screws that are typically included in body sets.
The new ride height gauge makes it easier to read Ride Height Readings on chassis and motor mounts particularly when they are chamfered like on the RX28.
These sleek-looking steel bumper weight set allow you to fine tune your weight bias on your Mini-Z when used in combination with any of our Carbon Fiber Bumpers. When running on bumpy or high grip environments, playing around with a little bit of nose weight can impact tremendously the behavior of your car. This weight set allows you to fine tune your nose weight in 1g increments. This is easily achieved by stacking the thru-hole weights and then clamping them down on the bumper with the threaded weight on top.
Included in the set is:
2x 1g thru weights
1x 1g threaded weight
1x M2x4CS Screw
1x M2x6CS Screw
M3 x 0.5mm Axle Shims to space out your rear axle and fine tune your set up (in some instances to center your rear axle!) Will Work on Cars like the GLR GT on the front as well.
Dieses Set-up Board ist aus 3mm Carbon Fiber gefertigt. Es misst 165x200mm und hat die perfekte Grösse, um bequem darauf zu arbeiten und in Deinem Koffer mitzureisen. Auf dem Setupboard befindet sich eine runde Wasserwaage und 4 verstellbare, gefräste Aluminiumfüsse, um das Setupboard eben aufzustellen und damit die Einstellungen für Dein Auto genauer zu machen. Die neue Version 2 des Boards enthält ausserdem gefräste Vertiefungen, damit Du lose Teile wie Karosserieclips und Radmuttern darin ablegen kannst. Video
It's finally here! Our all new Gear differential was designed to be a high quality and high performance addition to your 1/28 scale car. More rotation and harder acceleration than the ball differential yields a car that is often about a tenth faster to drive in high traction surfaces. The feel of this gear diff is very balanced and this makes the acceleration super smooth and strong. At only about 4.7g, it is also super light for less rotational mass.
The gear diff is sealed from the elements as the gears are inside a machined aluminum case in which you can larger amounts of grease to change the behavior of the differential action. The ticker the grease, the lower response into the corner, but this could be at the expense of a little bit of exit traction. We don't recommend going too heavy on the oil (maybe use no more than 1 or 2k CST oil), but you can use oil with no leakage at the spur and only slight leaking at the outputs.
MANUAL
**Please not the diff is not sealed at the bearings, so it is not designed to be "filled" with oil , but a healthy amount can be used when building. Left hub is not included.
Das Reflex V3 Werkzeugset - jetzt mit einem neuen Griff Design und zusätzlich mit einem Philips 00 Kreuzschraubenzieher, welcher sich bestens für die kleinen Pivot Schrauben des RX28 eignet. Das V3 Werkzeugset kommt wieder in einem praktischen Etui, welches die Werkzeuge schützt und Ordnung hält. Es beinhaltet alle notwendigen Werkzeugschlüssel, um deinen RX28, GL Racing, RTA oder MWX zu montieren. Das Werkzeugset enthält: Inbus-Schrauber:0,9mm1,3mm1,5 mmBox-Schlüssel:4.0mm4,5 mm Phillips-Schrauberzieher:#0#00
Solide, hochwertige Stahllager zu einem tollen Preis. Dies sind einige der besten Stahllager, die Sie heute bekommen können. Wenn Keramik nicht Ihr Ding sind, ist dies eine gute Ersatzlager für Ihre M3 Vorderachse Auto gesetzt.***Solid, high quality steel bearings at a great price. These are some of the best steel bearing you can get today. If ceramics are not your thing, this is a good replacement bearing set for your M3 Front Axle Car.